Burkert PTB 01 ATEX 2175 Operating Instructions Manual Download Page 7

7

General information

to avoid the risk of explosion, the following must be observed 

for operation in explosion-risk areas:

 

Information on the temperature class, ambient temperature, 

degree of protection and voltage on the type label for explosion-

risk areas.

 

Installation, operation and maintenance may only be performed 

by qualified specialists. 

 

The  applicable  safety  regulations  (including  national  regula-

tions) as well as general technical standards must be observed 

during setup and operation. 

 

Repairs may only be performed by the manufacturer.

 

The device must not be exposed to any mechanical and/or 

thermal loads which exceed the limits specified in the operat-

ing instructions.

general hazardous situations.

To prevent injury, ensure:

 

Secure system/equipment against unintentional activation.

 

Observe the direction of flow during installation.

 

After an interruption in the power supply or pneumatic supply, 

ensure that the process is restarted in a defined or controlled 

manner.

 

Don’t use the device as a lever when screwing the valve into 

the line.

Failure to observe this operating manual and its operating 

instructions  as  well  as  unauthorized  tampering  with  the 

device release us from any liability and also invalidate the 

warranty covering the devices and accessories!

general infOrmatiOn

4.1 

Contact addresses

germany

Bürkert Fluid Control Systems

 

Sales Center

 

Christian-Bürkert-Str. 13-17

 

D-74653 Ingelfingen

 

Tel.  + 49 (0) 7940 - 10 91 111

 

Fax  + 49 (0) 7940 - 10 91 448

 

E-mail: [email protected]

international 

Contact addresses can be found on the final pages of the printed 

operating instructions.
And also on the Internet at: 

www.burkert.com

4.2 

Warranty

The warranty is only valid if the device is used as intended in accor-

dance with the specified application conditions.

4.3 

Information on the Internet

The operating instructions and data sheets for Type AC21 can be 

found on the Internet at: 

www.burkert.com

 

 Typ 6106

english

PTB 01 ATEX 2175

Summary of Contents for PTB 01 ATEX 2175

















Reviews: