background image

33

Start-up

Type 3281

8.5.7 

X.LIMIT - Limitation of the mechanical valve adjustment range

This function limits the (physical) control range to predetermined % values (bottom and top). The valve 

adjustment range of the limited adjustment range is set equal to 100%. If the limited valve control range is left 

during operation, negative actual positions or actual positions greater than 100% are displayed.

Factory setting: Limit bottom setting range = 0%, limit top setting range t = 100%

Setting ranges: 

Limit bottom setting range:   

0...20% of the total setting range 

limit top setting range:    80...100% of the total setting range

Limited setting 

range

Unlimited setting 

range

Physical setting 

range (%) 

 

Limited 

setting range 

(%) 

 

Set-point value [mA](

INPUT

)

Fig. 15:  Diagram X.LIMIT

8.5.8 

CUTOFF

CUTOFF_min - Sealing function for positioners/process controllers

This function ensures that the valve is tightly closed outside the control range Enter limits here for the set-

point position (CMD) or process set-point value from which the actuator is completely closed.

CUTOFF_max - Opening function for positioners/process controllers

This function ensures that the valve opens 100% outside the control range Enter limits for the set-point 

position (CMD) or process set-point value from which the actuator opens completely.

english

Summary of Contents for 20010867











































Reviews: