manualshive.com logo in svg

BURGER MOTORSPORTS 135, Installation Manual

Share
Download
BURGER MOTORSPORTS 135 Installation Manual Download Page 4

Juice Box Stage 3 Professional (Pin out) Installation Guide – 5/13/09 

 

 

 

 
JB3 Pin Out Installation Guide 

 

© 2009 Copyright Burger Motor Sports, LLC 

 

3 / 9 

 

Large black subconnector: 
 
JB3 yellow: slot 10 (boost, yellow wire)  
JB3 light red: slot 11 (power, 5v reference, blue/yellow wire)  
JB3 brown: slot 17 (air intake temperature, red/yellow wire)  
JB3 white: slot 29 (crank position, yellow wire)  
JB3 black: slot 32 (ground, red/black wire)  
 
 
White subconnector:  
 
JB3 purple: slot 7 (boost solenoid 1, white/grey wire)  
JB3 green: slot 14 (boost solenoid 2, white wire)  
JB3 gray: slot 9 (fuel pressure, yellow/red wire, connect on all models)  
 
 
Small black subconnector:  
 
JB3 orange: slot 6 (oxygen sensor 1, yellow/white wire with 525 stamped on insulation)  
JB3 blue: slot 7 (oxygen sensor 2, yellow/white wire)  
 
 
Grey subconnector:  
 
JB3 dark red: slot 7 (throttle position, yellow/white wire. May be blue/white on 535)  
 

Summary of Contents for 135











Reviews:

No comments

Brands by name

Popular brands

Load more brands