background image

Manual-HotAir06-sdo-one-E

page 5 / 10

tool. We recommend the use of our PCB carrier 625 to handle the placement an removal of the
PCB.
When the oven produces too much smoke, pull the plug and close the door. This will extinct the
flames.

Do  not put any flammable materials near or on the reflow–oven

, don’t  block  the ventilation

grate.
Don’t touch the cover of the oven, it can be hot. 

You risk serious burning of your skin

.

Exhaust
Use the oven only in well ventilated rooms.

 Follow the safety rules of your paste supplier. During

the soldering process gas and heat may be emissioned. The gases can be affect your health.
We recommend our extraction hood and fume extractor options!

Normal use:

The oven is developed only for soldering of PCBs , don’t use the oven for food, animals or heating
of other materials. You will lose warranty if you don’t commit to those rules. 
Don’t use the oven when it’s damaged or not working properly.
Check the properly working of the oven by following the checklist below:

1.

Check the door. The door must not be bent or damaged. After firing-up on the oven check
the closing mechanism by opening and closing door. The oven must respond to it. If not

DON’T USE THE OVEN

 but contact your dealer. Don’t use the oven when there is a piece

of material between the door latch and ceiling’s. When the door or ceilings are damaged
it’s dangerous to use the oven

2.

Check the hinge and safety door handles. Don’t use the oven if they are broken or loose.

3.

Check the door sealing. Are they are not damaged?

4.

Check if there are no dents in the oven space

5.

Check the line cord, plug and outlet. Be sure they are not damaged.

Clean the oven frequently, residues in the oven may cause fire or other dangerous situations.

Maintenance

The unit should only be maintained and repaired only by qualified personnel. Never try to do more in
the way of maintenance to your unit than the operating instructions allow. Beyond that, always con -
sult an expert for repair work.

Setup

Take over from the transport agent

After receiving and unpacking, check the machine for possible transport damages. In case of trans -
port damage, please inform your insurance, the transport company and the manufacturer / supplier.

Place of installation

The oven must be standing level and there must be sufficient room to the machine for operation and
maintenance (approx 1m on all sides). When setting up the machine all safety regulations and other
local regulations are to be observed.
The oven should be installed on a good accessible table. The surface must be flat and heat resist -
ant and able to support a load of 30kg. 

Inside the box you will find:

One spare quartz lamp

One tube XADO lubricant

This manual

The oven

Connections

Finally connect the machine to the mains (220V / 50Hz). Do not use the building socket for other
electrical devices! The building supply line must be protected by a 16 amp fuse. The machine itself
has an automatic 15 A fuse. 

Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany

Tel.: +49 (0) 2292/9 28 28 - 0, Fax: +49 (0) 2292/9 28 28 - 29, E-mail: [email protected]

Summary of Contents for HOT AIR 06 SDO ONE











Reviews: