manualshive.com logo in svg

BullFrog 2002 Spas, Owner'S Manual, Page: 16 / 42

Share
Download
BullFrog 2002 Spas Owner'S Manual Download Page 16

Page 16 

Bullfrog Spas Owner’s Manual 

Pump 2 purges for 5 minutes at the beginning of each 

filter cycle. The low speed of pump 1 runs during fil-

tration and the ozone sterilizer (if installed) will be en-

abled. If any button is pressed during filtering, the 

ozone sterilizer (if installed) will be disabled for 30 

minutes.  

Temperature Display Inversion 

Press the “Warmer” or “Cooler” button, then the “Jets 1” 

button to invert display. Use the same sequence to 

revert back to normal display. 

Standby Mode 

The spa can be disabled when the filter needs to be 

serviced or when changing/servicing a JetPak™. Press 

the “Warmer” or “Cooler” button, then the “Light” but-
ton, and the display will show “

StbY

.” All spa functions 

will be disabled except for auxiliary freeze control. 

Press any panel button to resume spa operation. 

Freeze Protection 

If the temperature sensors detect a drop to 40°F within 

the heater, then pump 1 (and the heater if necessary) 

will automatically activate to provide freeze protection. 

The equipment stays on until the sensors detect that 

the spa temperature has risen to within 15°F of the set 

temperature. The pump will purge for 30 seconds to 2 

minutes at the end of the freeze condition. 

 

 

DIAGNOSTIC MESSAGES: 

No Message on Display: 

Power has been cut off to the 

spa. 

Action Required:

 The control panel will be disabled 

until power returns. Spa settings will be preserved for 

30 days with a battery back-up. 

 

“

OHH

” 

on Display: 

“Overheat” - The spa has shut 

down. One of the sensors has detected 118°F at the 

heater. 

Action Required:

 DO NOT ENTER THE WATER. Remove 

the spa cover and allow water to cool. Once the heater 

has cooled, reset by pushing any button. If spa does not 

reset, shut off the power to the spa and call your 

authorized Bullfrog Portable Spa Dealer. 

 

“

OH5

” 

on Display: 

“Overheat” - The spa has shut 

down. One of the sensors has detected that the spa 

water is 110°F. 

Action Required:

 DO NOT ENTER THE WATER. Remove 

the spa cover and allow water to cool. At 107°F, the spa 

should automatically reset. If spa does not reset, shut 

off the power to the spa and call your authorized 

Bullfrog Portable Spa Dealer. 

 

“

ICE

” 

on Display:

 “Ice” - Auxiliary Freeze Sensor 

detects potential freeze condition. 

Action Required:

 No action required. The pumps will 

automatically activate regardless of spa status. 

Wiring Diagram: Deluxe Control System 

Summary of Contents for 2002 Spas











































Reviews:

No comments