Bulldog Security PRO-SERIES 5002 Installation And Owner'S Manual Download Page 11

Page: 11 / 11

Dual Lock/Unlock Pulse Off

Disarm the system, press and hold Button #3 for 10 seconds or until the unit chirps once. Release Button #3, press

and release Button #4 within (2) two seconds, the unit will chirp (4) four times. The unit is now programmed for

Dual Lock/Unlock Pulse Off.

Setting Shock Sensitivity

Disarm the system and press Button #4 for (10) ten seconds or until the unit chirps once. Release Button #4 and

press and release Button #1, the unit will chirp once again. Impact the vehicle with the desired shock force. The

system will flash the parking lights once to show that the shock setting was accepted.

Programming New Transmitters (Up to (4) four transmitters allowed)

Disarm the system and press Button #1 for (10) ten seconds. The unit will arm-up in silent mode, flash the parking

lights once and will chirp once after the (10) ten seconds. Release Button #1 on the working transmitter and immediately

press any button on the new transmitter. The parking lights will flash twice indicating that a new transmitter has

been programmed.

Clearing the Unit Memory

Attach the Major trigger input wire (YELLOW) to Ground, then cycle the Ignition Key from off to on (run) (6) six

times within (5) five seconds, the parking lights will flash twice. The units memory is cleared. Unplug all harnesses

from the unit and wait 30 seconds. Plug the unit back in and use the remote transmitter. The unit is back to factory

settings.

Summary of Contents for PRO-SERIES 5002











