Bullard LANCER Instruction Manual Download Page 6

Page: 6 / 26

Component Concept

The approved respirator consists of six (6) components:

1. Respirator Helmet Assembly

L H O

Standard oval front

2. Air Delivery System

ADS

One size fits most inflatable collar

3. Half Mask Assembly

(Choose one)

LMS

Small

LMM

Medium

LML

Large

4. Outer Cape Assembly

(Choose one)

0032

Parka style

0072

Poncho style

5. Breathing Tube Assembly

(Choose one)

L30 1/4"

Industrial Interchange (Use with V10 hose)

L35 1/2"

Industrial Interchange ((Use with V20 hose)

ACL99

Vortex tube air conditioner (Use with V10 hose)

DC99

Dual-Cool air conditioner

6. Air supply Hose Assembly

(Choose one)

V20

Length as required

V10

Length as required plus one V27 quick disconnect

NOTE: The V27 quick disconnect consists of a V12 plus a V14 with Teflon

sealing tape. For quality assurance reasons, it is factory assembled. The V27
connects the V10 hose to the breathing tube assembly.

CAUTION: Do not use a quick-disconnect coupling at the point-of-attachment
when using a V10 air supply hose. Use only a V12 or V13 fitting.

Summary of Contents for LANCER



























Search results

Summary of Contents for LANCER

Reviews:

Related manuals for LANCER

Brands by name

Popular brands

Bullard LANCER, Instruction Manual

Search results

Summary of Contents for LANCER

Reviews:

Related manuals for LANCER

Brands by name

Popular brands