Bullard LANCER Instruction Manual Download | Manualshive

Page: 2 / 26

background image

APPROVAL LABEL ................................................................................

1

GENERAL INFORMATION

..................................................................... 2

COMPONENT CONCEPT

................................................................... 3, 4

WARNINGS

......................................................................................... 5, 6

OPERATIONS

Protection ....................................................................................... 7
Breathing Air Requirements .......................................................... 7
Breathing Air Pressure .................................................................. 8
Breathing Air Supply Hoses and Hose Fittings ............................. 9
Breathing Air Pressure Table ......................................................... 9
Typical Breathing Air Source & Respirator Configurations............10

RESPIRATOR ASSEMBLY

Sizing the Headband .................................................................... 11
Adjusting Suspension for Vertical Fit ........................................... 11
Installing Suspension into Helmet ................................................ 11
Attaching Cape to Helmet ............................................................ 12
Installing Breathing Tube Assembly into Air Delivery System ..... 12

RESPIRATOR USE

Donning ................................................................................. 13, 14
Doffing .......................................................................................... 15

INSPECTION, CLEANING AND STORAGE

Outer Cape .................................................................................. 16
Suspension System...................................................................... 17
Helmet  ......................................................................................... 17
Lenses and Window Frame Gasket ............................................ 17
Half Mask ..................................................................................... 18
Breathing Tube Assembly ............................................................ 18
Air Delivery System  ..................................................................... 19
Air Supply Hose ........................................................................... 19
Storage  ........................................................................................ 19

PARTS AND ACCESSORIES FOR LANCER AIRLINE

RESPIRATOR

....................................................................... 20, 21

Lancer Respirator Replacement Parts...........................................22

RETURN AUTHORIZATION

................................................................. 23

TABLE OF CONTENTS

«
1
2
3
4
...
»

Summary of Contents for LANCER



























Reviews:

No comments

Related manuals for LANCER

Respironics OptionHome

Brand: Philips Pages: 9

Respironics CoughAssist T70

Brand: Philips Pages: 6

Respironics FitLife

Brand: Philips Pages: 11

Respironics SideStream HS860

Brand: Philips Pages: 14

Respironics Nuance

Brand: Philips Pages: 20

Respironics DreamWear

Brand: Philips Pages: 18

Respironics EasyLife

Brand: Philips Pages: 20

Respironics InnoSpire Mini

Brand: Philips Pages: 23

RESPIRONICS DreamWear Series

Brand: Philips Pages: 22

Respironics EE Leak 1 AF541

Brand: Philips Pages: 28

Respironics Family Soft Touch

Brand: Philips Pages: 71

RESPIRONICS Sami the Seal

Brand: Philips Pages: 73

Respironics InnoSpire Elegance

Brand: Philips Pages: 93

RESPIRONICS Pico Traditional Nasal Mask

Brand: Philips Pages: 180

RESPIRONICS Amara SE

Brand: Philips Pages: 214

Respironics Nuance Gel

Brand: Philips Pages: 248

Brand: Ultrafilter Pages: 2

MicroAir NE-U22V

Brand: Omron Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands