background image

14

INSTALLATION STEP 7

Install the Light 

•  

Press the release tabs on both sides of lens. 
Gently rotate lens back and downward until the 
lens hinge is in the fully open position. Do not 
remove the lens.

•  

Install a 100 watt maximum light bulb in each 
socket. Light bulb size should be A19, standard 
neck only. The lights will turn ON and remain lit for 
approximately 4-1/2 minutes when power is 
connected. Then the lights will turn OFF.

•  

Reverse the procedure to close the lens.

•  

Use A19, standard neck garage door opener bulbs 
for replacement.

NOTE:

 

Use only standard light bulbs. The use of 

short neck or speciality light bulbs may overheat the 
endpanel or light socket.

INSTALLATION STEP 8

Attach the Emergency Release 
Rope and Handle

•  

Thread one end of the rope through the hole in the 
top of the red handle so “NOTICE” reads right side 
up as shown. Secure with an overhand knot at 
least 1" (2.5 cm) from the end of the rope to 
prevent slipping.

•  

Thread the other end of the rope through the hole 
in the release arm of the outer trolley.

•  

Adjust rope length so the handle is 6 feet (1.83 m) 
above the floor. Ensure that the rope and handle 
clear the tops of all vehicles to avoid 
entanglement. Secure with an overhand knot.

NOTE: 

If it is necessary to cut the rope, heat seal the 

cut end with a match or lighter to prevent unraveling.

Trolley

NOTICE

Overhand
Knot

Emergency
Release Handle

Rope

Trolley
Release Arm

To prevent possible OVERHEATING of the endpanel or 
light socket:
•   DO NOT use short neck or specialty light bulbs.
•   DO NOT use halogen bulbs. Use ONLY incandescent.
To prevent damage to the opener:
•   DO NOT use bulbs larger than 100W.
•  ONLY use A19 size bulbs.

To prevent possible SERIOUS INJURY or DEATH from a 
falling garage door:
•  If possible, use emergency release handle to disengage 

trolley ONLY when garage door is CLOSED. Weak or 
broken springs or unbalanced door could result in an 
open door falling rapidly and/or unexpectedly.

•  NEVER use emergency release handle unless garage 

doorway is clear of persons and obstructions.

•  NEVER use handle to pull door open or closed. If rope 

knot becomes untied, you could fall.

Lens Hinge

100 Watt (Max)

Standard Light Bulb

Release Tab

Summary of Contents for 3255BM 1/2 HP





































Reviews: