Buick 2007 Terraza Owner'S Manual Download Page 158 | Manualshive

Page: 158 / 562

background image

Reprogramming a Single Universal
Home Remote Button

To program a device to Universal Home Remote
using a Universal Home Remote button
previously trained, follow these steps:

1. Press and hold the desired Universal Home

Remote button. Do not release the button.

2. The indicator light will begin to flash after

20 seconds. While still holding the Universal
Home Remote button, proceed with Step
2 under “Programming Universal Home
Remote” shown earlier in this section.

For additional information on Universal Home
Remote, see

Customer Assistance Offices

on page 530

.

Storage Areas

Your vehicle’s large carrying capacity can store
many items. If the vehicle has an extended
wheelbase, it can carry even larger items. The
floor pins that are used to attach the seats, can be
used to secure larger loads.

Glove Box

If the glove box has a lock, put your key into the
lock and turn the key counterclockwise. To
open the glove box, pull the latch release.

The glove box door has a detent to prevent the
door from lowering too far. Open the glove
box until the door is partway open, then pull the
door down if you need it fully opened.

To close the glove box, the door must be pushed
up past the detent. To lock the glove box, put
your key into the lock and turn the key clockwise.

Cupholder(s)

There are cupholders located below the center
instrument panel switchbank. The cupholders have
a rubber liner that can be removed, so that
larger cups can fit into the cupholders. You can
also remove the liner to clean it.

To use the cupholders, pull the tray out. Push the
tray back when not in use.

Your vehicle may be equipped with cupholders in
the second row.

158

«
...
156
157
158
159
160
...
»

Summary of Contents for 2007 Terraza



















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Terraza

Brand: Jeep Pages: 25

Brand: Jeep Pages: 51

Brand: Farenheit Pages: 8

GRAND CHEROKEE 2023

Brand: Jeep Pages: 108

3-series convertible

Brand: BMW Pages: 98

Automotive 31006

Brand: KRAFTWERK Pages: 2

Brand: Ranger design Pages: 24

Brand: Maserati Pages: 302

Brand: Edelbrock Pages: 2

Brand: Mercedes-Benz Pages: 93

Brand: Connects2 Pages: 8

Ridesmart KMA-610

Brand: KlipXtreme Pages: 12

Brand: Volvo Pages: 7

Brand: BabySafe Pages: 43

Brand: E-Lead Pages: 11

Brand: Whispbar Pages: 18

Brand: NavLinkz Pages: 26

Brand: Westin Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands