Buffalo AirStation Nfiniti WZR-HP-AG300H User Manual Download

Page: 163 / 176

WZR-HP-AG300H User Manual

128

Appendix E TCP/IP Settings

Windows XP

To configure TCP/IP in Windows XP, follow the procedure below.

Click [Start] > [Settings] > [Control Panel].

Double-click [Network].

Right click on [Local Area Connection], then click [Properties].

Select [Internet Protocol (TCP/IP)], then click [Properties].

To have DHCP set your IP address settings automatically, check [Obtain an IP address
automatically] and [Obtain DNS server address automatically].

To set your IP address settings manually, enter values for each setting. Examples:

If the router’s IP address is 192.168.11.1,

IP address

192.168.11.80

Subnet mask

255.255.255.0

Default gateway

192.168.11.1

Preferred DNS server

192.168.11.1

Alternate DNS server

blank

Click [Close].

Summary of Contents for AirStation Nfiniti WZR-HP-AG300H

















































































































































































Search results

Summary of Contents for AirStation Nfiniti WZR-HP-AG300H

Reviews:

Related manuals for AirStation Nfiniti WZR-HP-AG300H

Brands by name

Popular brands

Buffalo AirStation Nfiniti WZR-HP-AG300H, User Manual

Search results

Summary of Contents for AirStation Nfiniti WZR-HP-AG300H

Reviews:

Related manuals for AirStation Nfiniti WZR-HP-AG300H

Brands by name

Popular brands