Buffalo AirStation Nfiniti WZR-HP-AG300H User Manual Download

Page: 143 / 176

WZR-HP-AG300H User Manual

108

Chapter 6 - Troubleshooting

Cannot connect to the Internet over wired connection.

• Make sure that your AirStation is plugged in!

• Check that the status LEDs of your AirStation are lit as below:

Power

Green light is ON

Router

Green light is ON or OFF (depending on your environment)

Diag

OFF

LAN

Green light is ON or flashing

Internet Green light is ON or flashing

• Make sure that your computer is set to [obtain an IP address automatically]. (See appendix E)

• Restart your AirStation.

Cannot access the web-based configuration Interface.

• See chapter 4 for instructions to open the AirStation’s configuration interface.

• Enter the correct username and password to login to the configuration interface. The factory

defaults are “root” (in lower case) for the username and a blank password (enter nothing). If you
changed the password, enter the new password that you set.

• Verify that your web browser is not set to use proxies.

• Make sure that your computer is configured to [Obtain an IP Address Automatically.] (See appendix

• Restart your AirStation.

Summary of Contents for AirStation Nfiniti WZR-HP-AG300H

















































































































































































Search results

Summary of Contents for AirStation Nfiniti WZR-HP-AG300H

Reviews:

Related manuals for AirStation Nfiniti WZR-HP-AG300H

Brands by name

Popular brands

Buffalo AirStation Nfiniti WZR-HP-AG300H, User Manual

Search results

Summary of Contents for AirStation Nfiniti WZR-HP-AG300H

Reviews:

Related manuals for AirStation Nfiniti WZR-HP-AG300H

Brands by name

Popular brands