manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

5.15

TRANSMISSION INSTALLATION

INSTALLATION

TOOL NAME

PART NUMBER

INSTALLER

B-43985-3

GUIDE

B-43985-4

TRANSMISSION FIXTURE

B-46285 (4)

NOTES

After re-installing the transmission assembly, verify that all
parts have been properly installed. See:

•

5.12 MAIN DRIVE GEAR AND BEARING

•

5.11 TRANSMISSION ASSEMBLY

•

5.14 TRANSMISSION LEFT CASE BEARINGS

•

5.13 TRANSMISSION RIGHT CASE BEARINGS

•

Make sure crankcase does not begin to tilt when pressed
onto transmission assembly. It may be necessary to place
press ram on transmission installer closer to mainshaft to
keep the crankcase level.

•

When removing crankcase and transmission assembly
from fixture, make sure mainshaft 1st gear does not fall
off shaft. Gear could be damaged if it strikes a hard sur-
face.

1.

See 

Figure 5-86

. Place transmission assembly onto

TRANSMISSION FIXTURE (Part No. B-46285 (4)) on
arbor press (1).

2.

Install transmission remover/installer tool GUIDE (Part
No. B-43985-4) (2) over the end of the countershaft.

3.

See 

Figure 5-87

. Place left case half over transmission

assembly and install transmission remover/installer tool
INSTALLER (Part No. B-43985-3) (1) into crankcase.

4.

Press crankcase onto transmission assembly until it bot-
toms out.

5.

Remove GUIDE (Part No. B-43985-4) from end of coun-
tershaft.

6.

Remove left crankcase half and transmission assembly
from fixture (5).

7.

Install left crankcase half and transmission assembly in
engine stand.

1

2

3

4

sm00342

1.

Arbor press

2.

Guide

3.

Countershaft and gears

4.

Transmission fixture

Figure 5-86. Transmission Assembly in Fixture (Typical)

HOME

2010 XB Service: Drive/Transmission  5-51

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Dakota Digital VHX systems Operating Manual preview
VHX systems
Brand: Dakota Digital Pages: 6
R&G LP0107BK Fitting Instructions Manual preview
LP0107BK
Brand: R&G Pages: 14
AKE PowerCom INNOVA Plus Business Quick Start Manual preview
PowerCom INNOVA Plus Business
Brand: AKE Pages: 2
SC MOTO NOSTRA MN4602 Assembly Instructions Manual preview
MOTO NOSTRA MN4602
Brand: SC Pages: 8
SUOMY MX SPEED Manual preview
MX SPEED
Brand: SUOMY Pages: 26
DYNATEK D32-1 Installation Instructions preview
D32-1
Brand: DYNATEK Pages: 4
AdMore Lighting LEDV46-T-TS LIGHT KIT Installation Instructions preview
LEDV46-T-TS LIGHT KIT
Brand: AdMore Lighting Pages: 4
Thermo Soles TS-03 Instructions Manual preview
TS-03
Brand: Thermo Soles Pages: 13
LSK FuelGaugePro FGP-SENSOR Installation Manual preview
FuelGaugePro FGP-SENSOR
Brand: LSK Pages: 11
Yamaha BWS CW50L Owner'S Manual preview
BWS CW50L
Brand: Yamaha Pages: 68
Benelli TRK249 Manual preview
TRK249
Brand: Benelli Pages: 39
Benelli Tornado TNT600 Owner'S Manual preview
Tornado TNT600
Brand: Benelli Pages: 64
Honda CRF250L 2019 Owner'S Manual preview
CRF250L 2019
Brand: Honda Pages: 117
Honda CRF250L/LA Rally 2020 Manual preview
CRF250L/LA Rally 2020
Brand: Honda Pages: 139
Honda CRF110F 2019 Owner'S Manual preview
CRF110F 2019
Brand: Honda Pages: 134
Honda CRF 150R 2007 Owner'S Manual preview
CRF 150R 2007
Brand: Honda Pages: 191
Honda CG150 Job Owner'S Manual preview
CG150 Job
Brand: Honda Pages: 222
hepco & becker 7007513 00 01 Mounting Instructions preview
7007513 00 01
Brand: hepco & becker Pages: 2

Brands by name

Popular brands

Load more brands