manualshive.com logo in svg

Buell 2005 FIREBOLT, Service Manual

The Buell 2005 FIREBOLT Service Manual is a comprehensive guide that allows you to maintain and repair your motorcycle with ease. Download this manual for free from our website, ensuring you have the necessary instructions to efficiently service your Buell FIREBOLT and keep it running smoothly.

Share
Download
background image

 

2005 Buell Firebolt: Fuel System

4-7

 

HOME

 

CODE TYPES

 

There are two types of trouble codes: current and historic.
Certain codes are also called functional codes. Historic codes
can be read using the check engine lamp diagnostics. 

All trouble codes reside in the memory of the ECM until the
code is cleared by DIGITAL TECHNICIAN (Part No. HD-
44750) or a total of 50 trips has elasped. A trip consists of a
start and run cycle, the run cycle lasting at least 30 seconds.
After the 50 trip retention period, the trouble code is automat-
ically erased from memory providing that no subsequent
faults of the same type are detected in that period.

 

NOTE

Trouble codes relating to the fuel injectors or the ignition coil
can only be fully diagnosed during actuation. For example, a
problem with the ignition coil will be considered a current fault
even after the problem is corrected, since the ECM will not
know of its resolution until after the coil is activated by vehicle
start sequence. In this manner, there may sometimes be a
false indication of the current trouble code.

 

Current

 

Current trouble codes are those which presently disrupt
motorcycle operation. See the appropriate flow charts for
solutions.

 

Historic

 

If a particular problem happens to resolve itself, the active
status problem is dropped and it becomes a historic fault
rather current fault.

Historic trouble codes are stored for a length of time to assist
in the diagnosis of intermittent faults. The check engine lamp
will not turn on during normal operation if only historic codes
are present.

It is important to note that historic trouble codes may also be
present whenever the system indicates the existence of a
current fault. See 

4.4 CHECKING FOR TROUBLE CODES

 if

multiple trouble codes are found.

 

Functional

 

Trouble codes 52 through 56 are considered to be functional
codes. They indicate an internal problem with the ECM (trou-
ble codes 52 through 55) or with the camshaft sensor/timing
(trouble code 56).

 

RETRIEVING TROUBLE

 

CODES

 

The fuel injection system provides two levels of diagnostics.

 

●

 

The most sophisticated mode employs using a computer
based diagnostic package called DIGITAL TECHNICIAN
(Part No. HD-44750).

 

●

 

The other mode requires using the check engine lamp.
See 

4.5 CHECK ENGINE LAMP DIAGNOSTICS

  for

more information.

 

MULTIPLE TROUBLE  CODES

 

The throttle position, cam position and bank angle sensors
are all connected to the same reference line (5v REF). If this
line goes to ground or open, multiple trouble codes (codes 11
and 56) may be set. 

Also, the ECM, fuel pump, fuel injectors and ignition coil all
r12 volts from the ignition relay. If this line should go
to ground the ignition fuse will open.

Always start with the trouble code having the lowest numeri-
cal value. See 

Table 4-7.

 

CHECK ENGINE LAMP BLINKS

 

In addition to alerting the rider to trouble codes, the check
engine lamp will blink during operation to warn of potentially
damaging engine operating temperatures. If the key is in the
on position and the check engine lamp is blinking, the engine
is at a potentially damaging temperature. While this condition
is in effect, the ECM will reduce engine power to assist in
cooling the engine down to a safe operating temperature. The
check engine lamp will blink until the engine has cooled to a
safe operating temperature. This will not set a trouble code.

Summary of Contents for 2005 FIREBOLT














































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2005 FIREBOLT

GAS GAS TXT PRO - 2007 Parts List preview
TXT PRO - 2007
Brand: GAS GAS Pages: 70
MSA V-Gard 500 Series Quick Manual preview
V-Gard 500 Series
Brand: MSA Pages: 2
HERO ACHIEVER 150 Manual preview
ACHIEVER 150
Brand: HERO Pages: 68
BMW HP2 ENDURO Manual preview
HP2 ENDURO
Brand: BMW Pages: 139
Yamaha XS650SE Shop Manual preview
XS650SE
Brand: Yamaha Pages: 215
Yamaha XS1100SH Service Manual preview
XS1100SH
Brand: Yamaha Pages: 319
Yamaha TMAX 2020 Service Manual preview
TMAX 2020
Brand: Yamaha Pages: 688
Yamaha XMAX YP250R 2013 Owner'S Manual preview
XMAX YP250R 2013
Brand: Yamaha Pages: 94
Yamaha YZ85(Z) Owner'S Manual preview
YZ85(Z)
Brand: Yamaha Pages: 86
Yamaha YZ85 2013 Owner'S Manual preview
YZ85 2013
Brand: Yamaha Pages: 88
Yamaha TDM850'99 4TX-AE3 Service Manual preview
TDM850'99 4TX-AE3
Brand: Yamaha Pages: 43
Yamaha YZFR6Z(C) Owner'S Manual preview
YZFR6Z(C)
Brand: Yamaha Pages: 118
Yamaha TT-R125E Owner'S Manual preview
TT-R125E
Brand: Yamaha Pages: 92
Yamaha YZF600RT Owner'S Manual preview
YZF600RT
Brand: Yamaha Pages: 105
Yamaha YZF-R6T(C) Owner'S Manual preview
YZF-R6T(C)
Brand: Yamaha Pages: 111
Yamaha TT-R110E 2018 Owner'S Manual preview
TT-R110E 2018
Brand: Yamaha Pages: 88
Yamaha TT-R TT250RN Owner'S Manual preview
TT-R TT250RN
Brand: Yamaha Pages: 94
Yamaha STRATOLINER XV19CTSC Owner'S Manual preview
STRATOLINER XV19CTSC
Brand: Yamaha Pages: 100

Brands by name

Popular brands

Load more brands