Buderus Logano GC124 II/SP Installation And Service Instructions Manual Download Page 58

Page: 58 / 84

Installation and maintenance instructions Gas Boiler Logano GC124 II/SP • Issue 07/2006

We reserve the right to make any changes due to technical modifications.

Boiler inspection and maintenance

Pilot burner opera-

tion continues even-

Thermocouple monitors ignition flame, ignition flame generates voltage in

thermocouple and keeps ignition valve open.

Main burner operation

• thermocouple controls ignition flame.
• main gas solenoid valve opens.

Specified thermostat value (control) reached

Main valve closes, gas burner switches off. Ignition
flame is burning.

END

Start

Main burner

operating

Power interruption

System switches off. Does
the system restart when
power is restored?

Room thermostat (control) signals heat requirement

Vent damper opens.

Summary of Contents for Logano GC124 II/SP





















































































Search results

Summary of Contents for Logano GC124 II/SP

Reviews:

Related manuals for Logano GC124 II/SP

Brands by name

Popular brands

Buderus Logano GC124 II/SP, Installation And Service Instructions Manual

Search results

Summary of Contents for Logano GC124 II/SP

Reviews:

Related manuals for Logano GC124 II/SP

Brands by name

Popular brands