Buderus Logano GC124 II/SP Installation And Service Instructions Manual Download Page 56

Page: 56 / 84

Installation and maintenance instructions Gas Boiler Logano GC124 II/SP • Issue 07/2006

We reserve the right to make any changes due to technical modifications.

Boiler inspection and maintenance

START

Room thermostat (control) signals heat requirement

Vent damper opens.

Ignition spark generator operates

• ignition gas valve opens.

Pilot flame stand by

• ignition spark generator stops.

• main gas solenoid valve opens.

Main burner operation

• automatic ignition monitors ignition flame.

Specified thermostat value (control) reached

Main and ignition gas valves close, gas burners ex-
tinguished, vent damper closes.

Ignition burner operation

Ignition flame burns, automatic

ignition signals steady ignition

flame.

ignition flame does not burn, au-
tomatic ignition starts ignition at-

tempt, switches off after 90

seconds.

END

PHASE 1

Ignition attempt

PHASE 2

Main burner

operating

Power interruption

System switches off. Does
the system restart when
power is restored?

Pilot flame fault

Main gas valve closes,
ignition module starts
ignition attempt.

Summary of Contents for Logano GC124 II/SP





















































































Search results

Summary of Contents for Logano GC124 II/SP

Reviews:

Related manuals for Logano GC124 II/SP

Brands by name

Popular brands

Buderus Logano GC124 II/SP, Installation And Service Instructions Manual

Search results

Summary of Contents for Logano GC124 II/SP

Reviews:

Related manuals for Logano GC124 II/SP

Brands by name

Popular brands