Buderus Logalux SM300/1 Installation And Maintenance Manual Download

Page: 35 / 40

Replacement Parts

Logalux SM300/1 - SM400/1 - Technical specifications are subject to change without prior notice.

7.5

Tank Jacket System for SM400/1
Tank

Position

Part Nr.

Description

Number

5069166

Complete tank insulation package (Blue) SM/SF/SU400

5069168

Complete tank insulation package (White) SM/SF/SU400

Available components

63004232

Left side insulation piece (100 mm, 4") blue for SM400

63004233

Left side insulation piece (100 mm, 4") white for SM400

63004253

Top insulation piece

63004267

Top tank cover

63004234

Right side insulation piece (100 mm, 4") blue for SM400

63004235

Right side insulation piece (100 mm, 4") white for SM400

63004262

Complete rear cover set

Consisting of:

3x cover strips 100 mm (4") long

63004258

Complete front cover set

Consisting of:

63004269

Insert cover

100

Top front cover strip

110

Bottom front cover strip

120

63004252

Bottom foam insulation piece

130

63004268

Front access cover insulation piece

140

63004265

Front cover

150

Mounting screws

160

Additional small insulation pieces

Consisting of:

4 soft foam pieces D50 x 80

1 Soft foam piece 75x75x75

Tab. 7

Available spare parts for solar hot water heater SM400/1

Summary of Contents for Logalux SM300/1









































Search results

Summary of Contents for Logalux SM300/1

Reviews:

Related manuals for Logalux SM300/1

Brands by name

Popular brands

Buderus Logalux SM300/1, Installation And Maintenance Manual

Search results

Summary of Contents for Logalux SM300/1

Reviews:

Related manuals for Logalux SM300/1

Brands by name

Popular brands