Buderus Logalux SM300/1 Installation And Maintenance Manual Download

Page: 33 / 40

Replacement Parts

Logalux SM300/1 - SM400/1 - Technical specifications are subject to change without prior notice.

7.4

Tank access cover and anode rod
assembly for SM400/1

Position

Part Nr.

Description

Number

5592180

Magnesium anode rod 33 x 700 mm

63020949

Sectional links anode rod 4 section 723/693 mm complete

Available components

Solid or sectional links magnesium anode rod

5264278

Mounting assembly set (10 pieces)

Consisting of:

Flat washer

Insulation sleeve for anode

Flat washer

Lock washer

Hex head nut

100

Hex head nut

110

Flat washer

120

7079410

Grounding strap of anode rod

130

Washer

140

63014368

Tank access cover

Tab. 6

Available spare parts for access cover and anode rod for SM400/1 tank

Summary of Contents for Logalux SM300/1









































Search results

Summary of Contents for Logalux SM300/1

Reviews:

Related manuals for Logalux SM300/1

Brands by name

Popular brands

Buderus Logalux SM300/1, Installation And Maintenance Manual

Search results

Summary of Contents for Logalux SM300/1

Reviews:

Related manuals for Logalux SM300/1

Brands by name

Popular brands