REMOTE SCENARIO MODE - Configurator SPE=6
CONFIGURATION
This mode of operation is only possible if the system has a scenario module item F420.
The configuration in
A
and
PL1
of the interface must correspond to that of the scenario module to be controlled.
The configuration in
M1
determines the correspondence between the keys of the radio remote control and the scenarios saved in
the scenario module, according to the table given below.
A
0-9
PL1
1-9
M1
1-4
PL2
0
M2
0
SPE
6
M1
PL2
M2
PL1
A
SPE
Scenario number
scenario module
Configurator
M1=1
Configurator
M1=2
Configurator
M1=3
Configurator
M1=4
Scenario 1
Key 1
Scenario 2
Key 2
Scenario 3
Key 3
Scenario 4
Key 4
Scenario 5
Key 1
Scenario 6
Key 2
Scenario 7
Key 3
Scenario 8
Key 4
Scenario 9
Key 1
Scenario 10
Key 2
Scenario 11
Key 3
Scenario 12
Key 4
Scenario 13
Key 1
Scenario 14
Key 2
Scenario 15
Key 3
Scenario 16
Key 4
17
��������
���
Scenario
module F420
Self-learning key
Green LED
Layout of the
keys of control
L4572SB
1
2
3
4
To associate a radio control item L4572SB to interface L/N/NT4575SB,
proceed as follows:
1) Press the pin pushbutton on the interface for at least 3 seconds; the red LED shines steadily. Release the key.
2) Within 20 seconds press a key of the pair on the radio control which you want to program; the red LED flashes quickly indicating
that the programming has taken place.
3) At this point points 1 and 2 can be repeated for all the codes to be saved inside the interface,
up to a maximum of 128
.
To cancel a code from interface L/N/NT4575SB,
proceed as follows:
1) Press the pin pushbutton on the interface for at least 8 seconds (after 3 seconds the red LED shines steadily, after another 5
seconds it goes out). Release the key. The red LED lights up again.
2) Within 20 seconds press a key of the pair on the radio control whose programming is to be cancelled; the red LED flashes quickly
for about 2 seconds to indicate that the cancelling has taken place.
3) From this moment the pair of keys will not activate any commands until it has been reprogrammed.
To cancel all the programming of interface L/N/NT4575SB
, press the pin pushbutton for about 12 seconds (after 3 seconds the
red LED shines steadily, after another 5 seconds it goes out and after another 4 seconds it flashes quickly for about 2 seconds,
confirming that all the programmings have been cancelled). Release the key.
To program a scenario,
proceed as follows:
1) The scenario module must be in configuration with self-learning enabled (press the self-learning key so that its LED is green).
2) Press the pin pushbutton of interface L/N/NT4575SB for at least 3 seconds: the red LED shines steadily. Release the key.
3) Within 20 seconds press the key on the radio remote control for the scenario to be programmed; the red LED starts to flash
indicating that the programming mode is activated.
4) Set the scenario by means of the corresponding devices of the My Home system (ex. command, amplifier, touch screen, etc.)
5) Within 35 minutes press the pin key on the interface to quit the programming; the red LED goes out.
6) Repeat points 2 to 5 for all the scenarios to be programmed.
7) If you want to disable the possibility of programming or cancelling the scenario, press the scenario module self-learning key so
that its LED is red.
PROGRAMMING
After configuring the interface the four scenarios associated with remote control L4572SB can also be called by other remote controls
of the same type (up to a maximum of 128 commands).
PROGRAMMING