background image

10

ST-00000691-

344652

01

3

15

5

15

4

4

15

6

6

P

M

N

BUS

ON OFF

Master

Slave

ON

CTS

1

2

BTICINO

V.le Borri, 231

21100 (VA) ITALY

P

N

Slave

ON

CTS

1

2

17/03/2020

EN

Classe100 V16B handsfree video  

internal unit

This function notifies the status of the Door lock. If open the “LED Door lock” flashes, and if closed, the LED stays off.

Warning:

 the function can only be activated if required by the system - accessory devices are required.

DOOR STATUS function

4  Move the joystick up/down to select the ringtone to be associated 

(the ringtone is played)

6  Move the joystick up/down to select another call or the last page to 

exit

3  Press the joystick to continue

5  Press the joystick to confirm or wait for the timeout

When active, this function prevents the opening of the entrance panel door lock when the internal unit is in stand-by. Therefore, the opening of the door lock is only permitted when 
entrance panel and internal unit are in voice communication.

Note: 

when the function is active, all the keys in all the configurations requiring the activation of a door lock are disabled, and when they are pressed the white LED flashes.

Enabling the function

Safe Door Lock function

Move the corresponding microswitch to ON

Summary of Contents for 344652











Reviews: