manualshive.com logo in svg

BTECH S5 BATTERY VALIDATION SYSTEM SCM-600, Operating Manual

Share
Download
BTECH S5 BATTERY VALIDATION SYSTEM SCM-600 Operating Manual Download Page 34

34

S5 Battery Validation System

8

Check the 

impedance 

multipliers.

a. From the Communications window, click 

System Configuration.

b. In the System Configuration window, click the 

Impedance Multipliers tab.

c. In the Impedance Multipliers tab, click the 

Auto Multiplier Setup button. The system will 

measure the impedance across all the battery 

units in all the strings. 
If you get an error message after clicking the 

Auto Multiplier Setup button, you will need to 

generate the multipliers manually. Call BTECH 

Tech Support for assistance.

d. Wait for the process to finish. Depending upon 

how many battery strings you have, and how 

many units per string, it could take anywhere 

from 1 or 2 minutes to much longer than that. (It 

takes about 15 seconds per unit.)

d. When the impedance readings are finished, 

multiplier values will appear. Click OK to accept 

them.

Action

How to do it

Picture

Summary of Contents for S5 BATTERY VALIDATION SYSTEM SCM-600



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands