manualshive.com logo in svg

BTECH S5 BATTERY VALIDATION SYSTEM SCM-600, Operating Manual

Share
Download
BTECH S5 BATTERY VALIDATION SYSTEM SCM-600 Operating Manual Download Page 18

18

S5 Battery Validation System

5

Make sure the load 

current leads are 

connected.

Make sure each LCL wire contains a fuse.

6

Make sure all plugs 

are connected firmly.

Make sure each plug on the SCM-600, VM24, and CM-2 is inserted firmly and has all its wires 

installed.

7

Make sure all wires 

are intact.

Check all wiring for damage; replace if damage is found.

8

Make sure the CTs 

are connected to the 

CM-2s they were 

configured with.

Compare the serial 

number on each CT with 

the serial number pasted 

to the CM-2 it connects 

to. They should match.

9

Make sure the CTs 

are installed 

correctly.

• Make sure both red dots on the CT are facing 

the same way.

• Make sure the red dots are facing toward the 

positive side of the power supply, so that the 

current running through the CT goes from 

positive to negative.

10

Make sure the 

ambient thermistor 

will provide an 

accurate reading.

Make sure the thermistor attached to the SCM-600 is placed in a location that is the same 

temperature as the air around the batteries.

11

Make sure the 

batteries are stable.

Make sure the batteries have been unused for at least 72 hours before gathering data.

Action

How to do it

Picture

Serial number on CT

Matching serial number on CM-2

Summary of Contents for S5 BATTERY VALIDATION SYSTEM SCM-600



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands