21
EN
MANUALE_SP3600_BWT-A5 - Rev: 01/2020
able collection of decommissioned equipment for re-
cycling, processing and environmentally compatible
disposal contributes in avoiding possible negative
effects on the environment and health and promote
the reuse and/or recycling of device materials. Illicit
product disposal by the user may be punishable by
current national laws.
6. Operations and use.
Do not use glue, sealant or other chemical prod-
ucts on threads or other product parts.
To disconnect the product from the power
mains, remove the
power plug
from the
power
outlet
without pulling on the power cord.
6.1. Operating description.
The product you purchase is designed to move wa-
ter in swimming
pool
. The
rotor
turns and transfers
water from the
inlet
to the
outlet
.
6.2. Application range.
The product cannot be used to purify water for hu-
man consumption.
The product cannot be used to purify liquids other
than fresh water.
The product was designed and constructed to
operate in above-ground fresh swimming
pool
,
located outdoors.
This powerful and reliable product can be used in
swimming
pool
, together with a
filter
, for water treat-
ment.
6.3. Use.
Cutting and/or altering the power cord is strictly
prohibited.
The product cannot be used to purify water for
human consumption.
The product cannot be used to purify liquids
other than fresh water.
The product cannot be used for medical/thera-
peutic purposes,
Dry operation
s are prohibited.
6.4. Operating limits and environmental limits
.
• Maximum water temperature: 35 [°C].
• Minimum water temperature: 4 [°C].
6.5. Safety devices and signalling.
The product is equipped with a
thermal protector
.
Following any
thermal protector
operation, check
the causes that originated the product’s malfunction.
For this purpose, please consult the “Troubleshoot-
ing” section.
The product shall go back to normal operating condi-
tions after it has cooled down (about 2÷3 hours) and/
or the caused that triggered the
thermal protector
have been eliminated.
6.5.1.
Power plug
with
residual current device
(RCD,
when included).
Before turning on the product, always press the
RESET button. Check
power plug
with
residu-
al current device
operations by pressing the TEST
button (T).
Do not attempt to repair or open the
power plug
with
residual current device
; in the event of fault,
replace the entire
power plug
with
residual current
device
with the power cord.
The
power plug
with
residual current device
does
not replace mandatory electrical safety components:
the electrical system must meet current internation-
al and/or national regulations. If necessary, contact
specialised technicians.
The
power plug
with
residual current device
is an
additional electrical safety component able to cut
off a circuit in the event of fault. In order for it to work,
it must:
• always be in the vertical position,
• always be clean and free of dust or water,
• be connected to a perfectly efficient ground line,
• check
residual current device
operations before
turning on the product (see below).
6.5.2. Checking
residual current device
operations.
Plug the
power plug
with
residual current device
into
the
power outlet
:
1. press the RESET button to allow the product to
be turned on: the light turns red.
2. press the TEST (T) button to test residual current
device operations: the light turns off and the
residual current device
cuts off electrical power,
therefore the product cannot be turned on unless
the RESET button is pressed again.
If the
residual current device
triggers (turns off the
product) during product use, unplug the
power plug
with
residual current device
from the
power outlet
and do not use the product. Contact a specialised
technician.
6.6. Hazards and risks.
The product is powered electrically, so maximum dili-
gence in its installation and maintenance is required,
in order to avoid danger. Please pay particular at-
tention to:
• the conditions of its power cord, which must not
be damaged (Fig. 15);
• do not use the product without its pre-
filter
basket
(Fig. 19, # 1), when present, otherwise the prod-
uct may jam or be irreparably damaged;
• when using any type of stop valve make sure the
line is completely open as the product must never
run with valves closed.
7. Routine, scheduled and extraordinary
maintenance.
Before beginning any work, remember to unplug
the electrical plug from the electrical socket.
Do not lubricate and/or use detergents and/or
chemical products to clean the product.
All extraordinary maintenance (replacement of
supply cord, etc.) must be carried out by spe-
cialised technicians.
Replace any damaged and/or worn components as
quickly as possible; use only original spare parts. For
this purpose, please consult the “Retail and spare