manualshive.com logo in svg

BSC 615L, Operating Instructions Manual

Share
Download
BSC 615L Operating Instructions Manual Download Page 23

BCS Crusader Power Scythes

CPS/MAX/0817

 

Page 23

Risk Assessment

HAZARDS

RISK LEVEL

ACTION NEEDED

Machine tipping over

Low

Do not use on slopes over 25°. Work across 
slopes, never up and down.

Machine running away

Low

Operator presence control (see Power Unit 

manual) stops the machine driving if the operator 
releases the handlebars.  Always check operation 
before use. 

Lacerations

High

Remove the spark plug cap before carrying out 
any maintenance or cleaning. Always wear gloves 
when cleaning or lubricating the cutter bar blades.

Machine reversing and trapping 
the operator against an 
immoveable object 

High

Never reverse the machine with your back to a 
wall or similar object.

Burns

High

Be very careful of a hot exhaust. Turn off the 
machine before re-fuelling. Allow 1” air space in 
fuel tank.

Flying objects

Low

Never exceed ¼ throttle when mowing.

Foot injuries

High

Never let anyone stand in front of the machine 
when it is operating. Keep all pets and animals 
away.

Handlebar adjustment

Low

Always set the height and sideways position 

before operating the machine – never while it is 

moving.

Summary of Contents for 615L





























Reviews:

No comments

Brands by name

Popular brands

Load more brands