Bryant CONDENSING GAS FURNACE 355MAV Installation, Start-Up, And Operating Instructions Manual Download Page 24 | Manualshive

Page: 24 / 52

background image

WARNING:

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each appliance connected to the venting system being placed into operation could result
in carbon monoxide poisoning or death.
The following steps shall be followed for each appliance connected to the venting system being placed into operation, while all other
appliances connected to the venting system are not in operation:

1. Seal any unused openings in venting system.
2. Inspect the venting system for proper size and horizontal pitch, as required in the National Fuel Gas Code, ANSI Z223.1-2002/NFPA

54-2002 or the CSA B149.1, Natural Gas and Propane Installation Code and these instructions. Determine that there is no blockage
or restriction, leakage, corrosion and other deficiencies, which could cause an unsafe condition.

3. As far as practical, close all building doors and windows and all doors between the space in which the appliance(s) connected to the

venting system are located and other spaces of the building.

4. Close fireplace dampers.
5. Turn on clothes dryers and any appliance not connected to the venting system. Turn on any exhaust fans, such as range hoods and

bathroom exhausts, so they are operating at maximum speed. Do not operate a summer exhaust fan.

6. Follow the lighting instructions. Place the appliance being inspected into operation. Adjust the thermostat so appliance is operating

continuously.

7. Test for spillage from draft hood equipped appliances at the draft hood relief opening after 5 minutes of main burner operation. Use

the flame of a match or candle.

8. If improper venting is observed during any of the above tests, the venting system must be corrected in accordance with the National

Fuel Gas Code, ANSI Z223.1-2002/NFPA 54-2002 and/or CSA B149.1, Natural Gas and Propane Installation Code.

9. After it has been determined that each appliance connected to the venting system properly vents when tested as outlined above, return

doors, windows, exhaust fans, fireplace dampers and any other gas-fired burning appliance to their previous conditions of use.

Fig. 32—Control Center

A02278

FLASH

UPGRADE

CONNECTOR

(FACTORY

ONLY)

ACRDJ – AIR

CONDITIONING

RELAY DISABLE

JUMPER

HUMIDIFIER

TERMINAL (24-VAC

0.5 AMP MAX.

CONTINUOUS FAN

(CF) AIRFLOW

SETUP SWITCHES

COMMUNICATION

CONNECTOR

AIR CONDITIONING

(A/C) AIRFLOW

SETUP SWITCHES

MODEL PLUG

CONNECTOR

SW1 SETUP

SWITCHES AND

BLOWER OFF-

DELAY

STATUS AND COMM

LED LIGHTS

3-AMP FUSE

TRANSFORMER 24-VAC

CONNECTIONS

PL3 – ECM BLOWER

HARNESS

CONNECTOR

PL1 – LOW VOLTAGE MAIN

HARNESS CONNECTOR

EAC-1 TERMINAL

(115-VAC 1.0 AMP MAX.)

115-VAC (L1) LINE

VOLTAGE CONNECTIONS

115-VAC (L2) NEUTRAL

CONNECTIONS

PL2 – HOT SURFACE

IGNITER & INDUCER

MOTOR CONNECTOR

24-V THERMOSTAT

TERMINALS

FUTURE

APPLICATIONS

—24—

«
...
22
23
24
25
26
...
»

Summary of Contents for CONDENSING GAS FURNACE 355MAV





















































Reviews:

No comments

Related manuals for CONDENSING GAS FURNACE 355MAV

Brand: Labnics Equipment Pages: 23

Brand: Crown Boiler Pages: 6

Brand: SummerAire Pages: 5

Brand: Maytag Pages: 58

Brand: THERMOBILE Pages: 89

Brand: Carrier Pages: 16

Brand: York Pages: 8

Brand: Haier Pages: 57

356486-UUM-E-0109

Brand: Johnson Controls Pages: 6

Brand: Lennox Pages: 4

Brand: Lennox Pages: 5

Brand: Bananza Pages: 60

Brand: ICP Pages: 50

Brand: ICP Pages: 59

Brand: ICP Pages: 65

Energysaver RHFE-1004FTA

Brand: Rinnai Pages: 112

Elite OF23 Lo-Boy (Front Flue)

Brand: Lennox Pages: 39

Brand: Trane Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands