Bruker NMR 400 89 Ascend DNP User Manual Download Page 30

Page: 30 / 106

ZTKS0243 / Z31993 / 03

Transportation

3.2.1

Disposal

Keep the original boxes for future transportation.

If no further transportation is planned, dispose of the boxes according to environmentally
friendly regulations.

3.3

Transport Inspection

Investigate the delivery with regard to visible damage and completeness of delivery.

Transport control systems

The shipping and handling monitors (“Shock Watch“, “Tilt Watch“) on the boxes show if
the boxes were kicked or tilted during transportation.

Checks

Shock Watch: Follow instructions on the label.

Tilt Watch: Follow instructions on the label.

In case of damage

•

Accept delivery with reservation.

•

Make a documentation of all observable damage and add it to the transportation
documents.

•

Start complaint process.

•

Contact Bruker Service before installation.

The claim for damage expires after the fixed period.

Thus:

Report damages to Bruker Service immediately after detection of damage. For contact
information see page 9 of this document.

Summary of Contents for NMR 400 89 Ascend DNP











































































































Search results

Summary of Contents for NMR 400 89 Ascend DNP

Reviews:

Related manuals for NMR 400 89 Ascend DNP

Brands by name

Popular brands

Bruker NMR 400 89 Ascend DNP, User Manual

Search results

Summary of Contents for NMR 400 89 Ascend DNP

Reviews:

Related manuals for NMR 400 89 Ascend DNP

Brands by name

Popular brands