Step 7: Install the dryer belt.
»
Turn both tension adjustment knobs counter-
clockwise to move the roller inward. This allows
enough slack in the belt to loop around and
complete the splice.
»
The belt should be fed so that it rests on the top of
the dryer frame support channels.
»
Ensuring that the edges are even, connect the
two ends together by interlocking the splice teeth
and insert the splice wire completely through the
splice.
»
Turn both tension adjustment knobs clockwise to
move the roller out. Only adjust the pulley so that
the belt is snug – do not overtighten.
Step 8: Venting is optional. There is a vent section that
provides a 10” hole for installation of an exhaust pipe. The
pipe can slide into the hole. See Figure 4.
Step 9: Connect to power. See the attached wiring diagram.
Warning: This equipment is operated by high
voltage electrical power and can be dangerous.
Only a qualified electrician should connect
and service this equipment. Safe and proper
installation of this dryer is the customer’s
responsibility.
Note: The wiring of the electrical supply to the
dryer must be in accordance with all local, state,
and national codes.
Warning: A 50Amp Branch Circuit Over-current
Device is Required on supply power for this
machinery.
The resistance heaters of your dryer operate on 208 to
240 volts, single phase AC. Motors and control circuits
operate on 115 volts AC. A four wire system providing 208-
240VAC electrical power, a neutral (common) for the 115
volt system and a chassis ground is required.
Refer to the control panel wiring diagram accompanying
these instructions. Check the following:
»
Connect the neutral (white) to the main terminal
marked “N”.
»
Connect the copper or green ground to the chassis
using the grounding lug.
»
Connect the main power supply wires to the main
terminals marked “L1” and “L2”.
»
Ensure that 208-240 VAC is being delivered
through the breaker by testing across these lines.
»
Ensure that 115VAC is being delivered between
each of the power lines and the neutral line.
»
Main power lines should be rated to carry 125% of
the full load amperes (FLA).
Machine Adjustments
Belt Tension
Apply enough tension to keep the belt from slipping on the
roller. Excessive tension is unnecessary and may shorten
the useful life of the belt.
Belt Tracking
Run the belt on high speed with the heat off to determine
whether the belt is tracking correctly. The knobs in the
end of the roller take-up plates are used to adjust the belt
tension.
Belt tracking is adjusted with the knobs on the end of the
conveyor frame. Increasing the belt tension on one side will
cause the belt to track towards the opposite side of the dryer
frame. Decreasing the belt tension on one side will cause
the belt to track towards that side. Additional adjustments
my be required when the oven reaches full temperature or
as the belt stretches with wear.Temperature Display: This is
the temperature currently being read in the heat chamber.
Baffle Height
The feed end of the oven features adjustable heat baffles.
These can be lifted up and down manually after loosening
the red knobs. Set to the lowest height possible that the
garments will still pass under the baffle. Tighten the knobs
when the baffle is at the desired height.
Proprietary Information of:
4661 Stafford Ave. S.W.
Wyoming, MI 49548
Tel. (616)249-0200
Fax. (616)249-3211
www.brownmfg.net
Unspecified Tolerances
x.xx ± 0.010
x.xxx ± 0.005
Remove all spatter, Burrs &
Break sharp edges.
ENG:
DATE:
SHEET:
Part Number : PR14450
Material:
Finish:
1 of 1
DAVID
11/30/2020
CRIMSON DRAGON 2430
97.500
50.159
33.141
32.125
35.120
POWER INPUT
BELT DIRECTION
ELECTRICAL SPECS
208V-240V
1 PH
32A
KNIGHT ENGINEERING DRAWING
POWER INPUT BOTTOM OF
CONTROL CABINET
Figure 4: Control panel layout
