BROWN 2000 Series Page 21 Owner'S/Operator'S Manual Download | Manualshive

Page: 21 / 60

background image

Cutter Operation

21

Before hitching cutter to your tractor, make sure all safety devices are installed on both the

cutter and the tractor.

Please follow all safety instructions and procedures.

Attach equipment to tractor.

Be sure the tractor is equipped with the correct category hitchpins, top link, a

certified roll-over protection structure (ROPS), and an enclosed operator-protective

cage to prevent hazards such as thrown, falling, or stationary objects from entering

the protective cage.

Be extremely careful when positioning tractor to hitch to the equipment.

Caution!

Never allow anyone between the tractor and the equipment during the

hitching process.

Be certain that the cutter has been lubricated properly and check oil level in gear

box prior to connecting driveline to tractor. Also, do not tighten the top link such that the

flex-link toggle is fully extended toward the tractor. The flex-link should be in a relaxed

position when on level ground See diagram 21-1 Page 21,.

Attach the driveline to the tractor.

When attaching driveline to PTO shaft, be cer-

tain that the quick-disconnect pin is properly seated.

Warning!

A loose driveline will disconnect and may cause personal injury or prop-

erty damage.

STOP

21-1: Relaxed Top Link Position

«
...
19
20
21
22
23
...
»

Summary of Contents for 2000 Series





























































Reviews:

No comments

Related manuals for 2000 Series

Brand: VeEX Pages: 2

Brand: JB-Lighting Pages: 48

Brand: Ultimaker Pages: 38

Brand: A&D Pages: 2

Brand: A&D Pages: 176

Brand: IDEAL Networks Pages: 10

Brand: jablotron Pages: 2

Brand: Jet Pages: 12

SC 2 Deluxe EasyFix

Brand: Kärcher Pages: 12

Brand: Kärcher Pages: 16

Brand: LA Audio Pages: 9

Brand: Rane Pages: 6

Brand: Rane Pages: 27

Brand: Ranger Products Pages: 6

Brand: Rane Pages: 88

Brand: Haag-Streit Pages: 21

Brand: GE Pages: 176

Brand: Triton Blue Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands