BROWER TIMING SYSTEM TCi-System User Manual Download

Page: 11 / 13

www.browertiming.com

Multiple System Setup

Up to five TCi systems can be used in the same area by using one of five

different radio frequency channels.

The

TCi-Timer, TC-Display, TCi-Smart Start,

and all

TCi-PhotoGates

must be set to the same frequency.

TCi-Timer

: Use the

Mode

button to scroll to the

FREQ

option. Select 0-4

TCi-PhotoGates

: Remove the aluminum case. Locate the blue

switch panel and shift a lever.

TCi-Smart Start

: when turning the system on, hold the on/off

button until ”FrE” displays on the screen. Select 0-4 then press

Enter

TC-Display

: Remove two small screws from the side of the display. Pull

the end cap out of the metal casing. Locate the blue switch panel and shift

a lever. (All switches up is FREQ 0)

More than one switch cannot be down at the same time.

Note: To avoid confusion mark each component on the outside with it’s

frequency.

1 2 3 4

Troubleshooting

Problem

One of my timing units does not power up.

Solution 1

All units require you to press and hold the power button for at

least 2 seconds to initiate the power up sequence.

Solution 2

Check the battery. The units will warn of a low battery by a

red flashing LED on the

TCi-PhotoGate A

. The

TCi-Smart Start

will

show “Lo” on power up

. The

TCi-Timer

has a low battery symbol on the

LCD. The units work for up to 20 more hours and 5 for the

TCi-Timer

with a low battery. If the unit will not turn on, check for dead battery.

See page 20 on how to replace batteries.

Problem

My timing system is setup correctly, but the

TCi-Timer

won’t

receive a signal.

Solution

Check to see if all the system components are on the same radio

frequency. See FREQ on page 12.

Problem

I occasionally miss signals.

Solution 1

For long range setups see RSSI on page 12.

Solution 2

Setup the

TCi-PhotoGate A

and set the

TCi-Timer

to the

RSSI mode. Trigger the

TCi-PhotoGate

while the

TCi-Timer

is in close

range. The RSSI reading should be about (95-114). If the RSSI reading

is close to 65 then the frequency channels are not matched correctly. See

page 12. If the RSSI reading is below 65 then the radio might be bad or an

antenna is broken.

Problem

My touch-pad is correctly installed, but doesn’t beep when I

press it or beeps multiple times when I press it.

Solution

Your touch-pad is worn out, order a new one. (60 day warranty,

$39 replacement)

Troubleshooting

If you are still not sure the system is functioning correctly, call us at 801-

572-5540

“I have found a problem, what do I do now?”

If the system has a defect go to:

www.browertiming.com

, click repair, and complete instructions to return

defective unit.

Summary of Contents for TCi-System














Search results

Summary of Contents for TCi-System

Reviews:

Related manuals for TCi-System

Brands by name

Popular brands

BROWER TIMING SYSTEM TCi-System, User Manual

Search results

Summary of Contents for TCi-System

Reviews:

Related manuals for TCi-System

Brands by name

Popular brands