background image

1

Read Before Use ......................................................................................................................................................... 2

Accessories ..................................................................................................................................................................................................... 2
Operating Precautions .................................................................................................................................................................................... 2

Creating Data for the Roll Feeder ............................................................................................................................... 3

Activating the Roll Feeder Function ................................................................................................................................................................ 3
Creating Data .................................................................................................................................................................................................. 4
Weeding Box Function .................................................................................................................................................................................... 5
Exporting Data as FCM File ............................................................................................................................................................................ 7
Sending Data to the Machine.......................................................................................................................................................................... 8

Installing the Roll Feeder ............................................................................................................................................ 9

Installing the Base Attachment to the Machine .............................................................................................................................................. 9
Installing the Roll Holder ............................................................................................................................................................................... 10
Loading Material Into the Roll Feeder ........................................................................................................................................................... 10
Checking the End of the Material.................................................................................................................................................................. 11
Evenly Trimming the End of the Material ...................................................................................................................................................... 12
Feeding the Material...................................................................................................................................................................................... 14

Retrieving Roll Feeder Data On the Machine and Cutting........................................................................................ 15

Retrieving Data on the Machine .................................................................................................................................................................... 15
Cutting........................................................................................................................................................................................................... 16
Trial Cutting ................................................................................................................................................................................................... 18
Trial Feeding.................................................................................................................................................................................................. 20
Changing the Cutting Start Position ............................................................................................................................................................. 21
Continuous Cutting ....................................................................................................................................................................................... 22

Removing the Roll Feeder To Feed Using a Mat ....................................................................................................... 23
Consumables/Maintenance....................................................................................................................................... 25

Replacement Criteria..................................................................................................................................................................................... 25
Replacing the Trimmer Blade........................................................................................................................................................................ 25
Cleaning the Trimmer Blade.......................................................................................................................................................................... 27

Troubleshooting........................................................................................................................................................ 28

When Material Has Become Jammed in the Machine .................................................................................................................................. 30

Error Messages.......................................................................................................................................................... 32

Cutting Machine Error Messages.................................................................................................................................................................. 32
CanvasWorkspace Error Messages .............................................................................................................................................................. 32

Useful Information ................................................................................................................................................... 33

Roll Feeder Usage......................................................................................................................................................................................... 33
Compatible Materials .................................................................................................................................................................................... 33
Examples of Materials That Can Be Used .................................................................................................................................................... 33
Non-Compatible Material .............................................................................................................................................................................. 35
Sizes of Rolled Material That Can Be Loaded Into the Roll Feeder .............................................................................................................. 36
Blades That Can Be Used ............................................................................................................................................................................. 36
Scanner Lever Position ................................................................................................................................................................................. 36

CONTENTS

Summary of Contents for ScanNCut DX







































Reviews: