Brother NV1250D Operation Manual Download Page 62 | Manualshive

Page: 62 / 212

background image

SEWING BASICS

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

60

■

Upper thread is too tight

If the bobbin thread is visible from the right side
of the fabric, the upper thread is too tight.

Note

z

If the bobbin thread was incorrectly
threaded, the upper thread may be too tight.
In this case, refer to “Installing the bobbin”
(page 29) and rethread the bobbin thread.

a

Wrong side of fabric

b

Right side of fabric

c

Upper thread

d

Bobbin thread

e

The bobbin thread is visible from the right side of
the fabric.

Each press of

makes the thread tension looser.

■

Upper thread is too loose

If the upper thread is visible from the wrong side
of the fabric, the upper thread is too loose.

Note

z

If the upper thread was incorrectly threaded,
the upper thread may be too loose. In this
case, refer to “Upper Threading” (page 31)
and rethread the upper thread.

a

Wrong side of fabric

b

Right side of fabric

c

Upper thread

d

Bobbin thread

e

The upper thread is visible from the wrong side of
the fabric.

Each press of

makes the thread tension tighter.

Memo

z

Press

to return the setting to its

default.

Note

z

If the upper thread is not threaded correctly
or the bobbin is not installed correctly, it
may not be possible to set the correct thread
tension. If the correct thread tension cannot
be achieved, rethread the upper thread and
insert the bobbin correctly.

«
...
60
61
62
63
64
...
»

Summary of Contents for NV1250D





















































































































































































































Reviews:

No comments

Related manuals for NV1250D

Brand: Janome Pages: 25

Brand: Janome Pages: 48

Brand: Xerox Pages: 182

Ellageo PLUS BLL2

Brand: Baby Lock Pages: 43

Brand: Baby Lock Pages: 71

Brand: Baby Lock Pages: 2

Brand: Baby Lock Pages: 2

A_LINE Maria BL23A

Brand: Baby Lock Pages: 78

A-LINE Natalie BL18A

Brand: Baby Lock Pages: 70

A-LINE Lauren BL450A

Brand: Baby Lock Pages: 12

Brand: Baby Lock Pages: 204

Brand: Baby Lock Pages: 24

Elissimo & Elissimo GOLD BLSO-BF2

Brand: Baby Lock Pages: 22

Brand: R.P.S. Corporation Pages: 23

KM 130/300 R Bp

Brand: Kärcher Pages: 372

Brand: Kärcher Pages: 16

BRC 30/15 C *JP

Brand: Kärcher Pages: 48

KM 130/300 R Bp

Brand: Kärcher Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands