manualshive.com logo in svg

Brother HL-5250DN series, Service Manual

Share
Download
Brother HL-5250DN series Service Manual Download Page 34

HL-5240/5250DN/5270DN/5280DW SERVICE MANUAL 

Confidential

 

1-21

3.8 

Print Speeds with Various Settings 

Print speed is up to 28 ppm for A4 size and 30 ppm for Letter size when loading A4 or Letter 
size paper from the paper tray in the plain paper mode. 

Actual print speed varies depending on the media type or paper size as shown in the tables 
below; 

 

<A4 / Letter size> 

Media type setting 

All models 

Transparency 28/30 

ppm 

Thin Paper 

28/30 ppm 

Plain Paper 

28/30 ppm 

Recycled Paper 

28/30 ppm 

Thick Paper, 
Envelopes, Env.Thin 

14 ppm 

Thicker/Bond Paper, 
Env.Thick 

3 ppm 

 

<Smaller size than A4 or Letter> 

Media type setting 

All models 

Transparency 28/30 

ppm 

Thin Paper 

28/30 ppm 

Plain Paper 

90 sec 28/30 ppm 

Æ

 14 ppm 

Recycled Paper 

90 sec 28/30 ppm 

Æ

 14 ppm 

Env.Thin 14 

ppm 

Thick Paper, 
Envelopes 

14 ppm 

Thicker/Bond Paper, 
Env.Thick 

3 ppm 

 

 
NOTE: 

• 

The print speed may vary according to conditions, such as paper size and paper tray. 

• 

When a smaller size paper than A4 or Letter is printed, the temperature on both edges of  

the fuser unit is much higher than the temperature on the center of the unit where the paper  
is fed depending on the setting or model.  Therefore, the print speed is slowed in order to  
decrease the temperature on the edges after the specified time, it is maximum print speed  
when you first start printing. 

• 

The actual print speed varies depending on the paper size. 

Summary of Contents for HL-5250DN series


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands