manualshive.com logo in svg

Brother HL-5250DN series, Service Manual

Share
Download
Brother HL-5250DN series Service Manual Download Page 298

CHAPTER 7 SERVICE SUPPORT SOFTWARE 

Confidential

 

7-10

• <Replace 

count> 

PF KITMP: 
PF KIT 1: 
PF KIT 2: 
PF KIT 3: 
FUSER: 
LASER: 
DRUM: 
TONER: 

• 

<Total Pages Printed> 

Previously Used Toner: 
Current Toner: 

• <Developing 

Bias> 

 

NOTE: 

* Some margin of error must be taken into consideration because coverage for the  
printable area of A4-size paper is calculated using video signals 

* If the firmware version is 1.02 or before, the maintenance information gives out false 
information on the remaining life of Drum.  To know the accurate information of Drum, 
print the Print Settings or upgrade the firmware version.   

(9) Print 

Settings 

If you want to know the drum unit life or the number of printed pages, you should print out 

the Print Settings. 
1. Contents 

overview 

The “Print Settings” is configured with two pages for HL-5240 and more than three 

pages for HL-5250DN/5270DN/5280DW. 

All pages have following terms in common: 
* Title 
* Model name 
* Serial number 
The setting indication is the same as the panel setting information, supporting 17 

languages. 

(ENG / FRE / GER / DUT / ITA / SPA / NOR / FIN / DAN / POR / SWE / CZE / POL / 

HUN / RUS / BUL / RUM) 

The descriptions on the third page or later are indicated in English only.

 

NOTE: 

• 

The descriptions printed in Print Settings vary depending on the countries. 

• 

It is also allowed you to print the print settings by pressing the 

Go

 button three times  

continuously when the front cover is closed and when the printer is in the ready  
mode. 

• 

Select Information, then Print Settings by pressing the 

Set

 button three times. 

(HL-5270DN/5280DW) 

 

Summary of Contents for HL-5250DN series


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands