manualshive.com logo in svg

Brother HL-5250DN series, Service Manual

Share
Download
Brother HL-5250DN series Service Manual Download Page 291

HL-5240/5250DN/5270DN/5280DW SERVICE MANUAL 

Confidential 

7-3

1.2 

User Maintenance Mode 

This section describes what the user should do when replacing the consumable parts. 

<Resetting the drum counter> 

The printed image may deteriorate when using the drum unit to a certain degree.  The printer 
detects how much the drum unit is used with the drum counter and lights up the 

Drum

 LED 

when the drum unit life is nearly at the end of its life to indicate to the user that the drum unit 
life reaches the end of its life soon, in order to prevent the printed image defects due to drum 
unit deterioration. 
The printer does not provide the function which resets the drum counter automatically when 
the drum unit is replaced with a new one.  If replacing the drum unit with a new one without 
resetting the drum counter, the counted value of the old drum unit is used continuously so 
that the 

Drum

 LED is not off. 

When replacing the drum unit with a new one, it is required to reset the drum counter 
following the steps below: 

<HL-5240/5250DN> 

(1)  Make sure that the printer is turned on and the 

Drum

 LED is blinking.  Press the front 

cover release button and then open the front cover. 

(2)  Press and hold down the 

Go

 button for about four seconds until all the LEDs light up.  

Once all four LEDs are lit, release the 

Go

 button. 

(3)  Take out the drum unit and toner cartridge ASSY. 

(4)  Put the new drum unit and toner cartridge ASSY back into the printer. 

(5)  Close the front cover. 

<HL-5270DN/5280DW> 

(1)  Press the front cover release button and then open the front cover. 

(2)  Keep pressing the 

Go

 button for about four seconds.  When the message of finishing 

resetting the drum counter, release the 

Go

 button. 

(3)  Take out the drum unit and toner cartridge ASSY. 

(4)  Put the new drum unit and toner cartridge ASSY back into the printer. 

(5)  Close the front cover. 

 

Summary of Contents for HL-5250DN series


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands