manualshive.com logo in svg

Brother HL-3140CW, User Manual

Share
Download
Brother HL-3140CW User Manual Download Page 165

Troubleshooting 

159

5

Cover is Open

The top cover is not closed 
completely.

Close the top cover of the machine.

The fuser cover is not closed 
completely or paper was jammed in 
the back of the machine when you 
turned on the power.

Close the fuser cover located inside the back 
cover of the machine.

Make sure paper is not jammed inside the back of 
the machine, and then close the fuser cover and 
press 

Go

 (see 

Paper is jammed at the back of the 

machine

 on page 167).

Drums End Soon

The 4 drum units are near the end of 
their life.

Order a new drum unit set now so a replacement 
drum unit will be available when the LCD shows 

Replace Drums

 (see 

Drums End Soon

 

on page 119).

Drum End Soon: X

(X shows the toner 
cartridge or drum unit 
color that must be 
replaced. BK=Black, 
C=Cyan, M=Magenta, 
Y=Yellow.)

The drum unit for the color indicated 
on the LCD is near the end of its life.

Order a new drum unit for the color indicated on the 
LCD before you get a 

Replace Drum: X

 message.

Drum!

The corona wire on the drum unit 
needs to be cleaned.

Clean all four corona wires (one for each color) inside 
the drum unit by sliding the green tab (see 

Cleaning 

the corona wires

 on page 143).

The drum unit or the toner cartridge 
and drum unit assembly is not 
installed correctly.

Remove the toner cartridge and drum unit assembly, 
remove the toner cartridge from the drum unit, and 
reinstall the toner cartridge back into the drum unit. 
Reinstall the toner cartridge and drum unit assembly 
back in the machine. If the problem continues, 
replace the toner cartridge (see 

Replacing the toner 

cartridges

 on page 111).

Drum Stop

It is time to replace the drum unit.

Replace the drum unit for the color indicated on the 
LCD (see 

Replacing the drum units

 on page 121).

Fuser Error

The temperature of the fuser unit 
does not rise to a specified 
temperature within the specified 
time.

Turn the machine off, wait a few seconds, and then 
turn it on again. Leave the machine for 15 minutes 
with the power on.

The fuser unit is too hot.

Jam 2-sided

The paper is jammed underneath 
the paper tray or the fuser unit.

See 

Paper is jammed underneath the Paper Tray

 

on page 165.

Jam Inside

The paper is jammed inside the 
machine.

See 

Paper is jammed inside the machine

 

on page 169.

The toner cartridge was placed in 
the machine without the drum unit.

Put the toner cartridge into the drum unit, and then 
reinstall the toner cartridge and drum unit assembly in 
the machine.

Jam Manual Feed

The paper is jammed in the manual 
feed slot of the machine.

See 

Paper is jammed in the manual feed slot

 

on page 163.

Error message

Cause

Action

Summary of Contents for HL-3140CW















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands