manualshive.com logo in svg

Brother 9500 - HL 1660EN B/W Laser Printer, User Manual

The Brother 9500 - HL 1660EN B/W Laser Printer is an exceptional printing device that delivers sharp black and white documents with incredible speed and precision. To maximize your printer's potential, make sure to grab the free User Manual available for download at manualshive.com and unlock its full range of features and functionalities.

Share
Download
background image

CHAPTER 6 MAINTENANCE

6–7

Clean the printer interior as follows:

1. Turn off the printer and unplug the power cord.

2. Open the top cover of the printer and remove the toner cartridge.

3. Clean both sides of the paper access cover and transfer guide by

wiping off toner and paper particles with a dry, soft cloth. The paper
access cover can be lifted up to allow easier access for cleaning.

Fig. 6-6  Cleaning the Paper Access Cover

and Transfer Guide

4. Wipe off toner and paper particles from the top surface of the black

plastic paper guide with a dry, soft cloth.

Fig. 6-7  Cleaning the Paper Guide

5. Detach the cleaning brush from the top cover and clean the anti-static

teeth by sliding the brush several times.  After cleaning, replace the
brush in its slot.

6. Refit the toner cartridge as described in 

REPLACING THE TONER

CARTRIDGE.

7. Close the top cover of the printer and plug in the power cord.

Paper Access Cover

Transfer Guide

Paper Guide

Summary of Contents for 9500 - HL 1660EN B/W Laser Printer



































































































































































































































































Reviews:

No comments

Related manuals for 9500 - HL 1660EN B/W Laser Printer

Canon iPF650 - imagePROGRAF Color Inkjet Printer Basic Manual preview
iPF650 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 40
Canon iP90 - PIXMA Color Inkjet Printer Easy Setup Instructions preview
iP90 - PIXMA Color Inkjet Printer
Brand: Canon Pages: 2
Canon iPF650 - imagePROGRAF Color Inkjet Printer Install Manual preview
iPF650 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 16
Canon iP100 - PIXMA Color Inkjet Printer Setup Instructions preview
iP100 - PIXMA Color Inkjet Printer
Brand: Canon Pages: 2
Canon imageRUNNER ADVANCE C5560 Configuration And Installation Manual preview
imageRUNNER ADVANCE C5560
Brand: Canon Pages: 67
Canon imageRUNNER 3300 Reference Manual preview
imageRUNNER 3300
Brand: Canon Pages: 366
Canon IMAGERUNNER ADVANCE C5051 Getting Started preview
IMAGERUNNER ADVANCE C5051
Brand: Canon Pages: 252
Canon iPF710 - imagePROGRAF Color Inkjet Printer Operations preview
iPF710 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 2
Xerox EX Specification Sheet preview
EX
Brand: Xerox Pages: 2
Xerox EX Brochure & Specs preview
EX
Brand: Xerox Pages: 2
DataCard CP40 Manual preview
CP40
Brand: DataCard Pages: 2
Radio Shack TRS-80 Operation Manual preview
TRS-80
Brand: Radio Shack Pages: 57
TE Connectivity T3212 Quick Start Manual preview
T3212
Brand: TE Connectivity Pages: 2
TE Connectivity T3200 Replacement Instructions preview
T3200
Brand: TE Connectivity Pages: 2
Konica Minolta bizhub 160 Service Manual preview
bizhub 160
Brand: Konica Minolta Pages: 20
Ricoh Lanier AP206 Setup Manual preview
Lanier AP206
Brand: Ricoh Pages: 406
Evolis EDIKIO FLEX User Manual preview
EDIKIO FLEX
Brand: Evolis Pages: 45
Rice Lake SST4 Technical Manual preview
SST4
Brand: Rice Lake Pages: 86

Brands by name

Popular brands

Load more brands