manualshive.com logo in svg

Brother 9500 - HL 1660EN B/W Laser Printer, User Manual

The Brother 9500 - HL 1660EN B/W Laser Printer is an exceptional printing device that delivers sharp black and white documents with incredible speed and precision. To maximize your printer's potential, make sure to grab the free User Manual available for download at manualshive.com and unlock its full range of features and functionalities.

Share
Download
background image

REGULATIONS

ix

IMPORTANT INFORMATION:  REGULATIONS

Federal Communications Commission Compliance Notice
(For U.S.A. only)

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

❏

Reorient or relocate the receiving antenna.

❏

Increase the separation between the equipment and receiver.

❏

Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

❏

Consult the dealer or an experienced radio/TV technician for help.

Important – About the Interface Cable

This printer has been certified to comply with FCC standards, which are
applied to the U.S.A. only. A shielded interface cable should be used
according to FCC 15.27(C). In addition, a grounded plug should be
plugged into a grounded AC outlet after checking the rating of the local
power supply for the printer to operate properly and safely.

☛

  Caution

Changes or modifications not expressly approved by Brother Industries,
Ltd. could void the user’s authority to operate the equipment.

International Energy Star Compliance Statement (For HL-1660
series only)

The purpose of the International Energy Star Program is to promote the
development and popularization of energy-efficient office equipments, which
includes computers, monitors, printers, facsimile receivers and copy machines
world-wide.
As an International Energy Star partner, Brother Industries, Ltd. has decided that
this product meets the guideline of the program.

Summary of Contents for 9500 - HL 1660EN B/W Laser Printer



































































































































































































































































Reviews:

No comments

Related manuals for 9500 - HL 1660EN B/W Laser Printer

SA F1 Series Installation And Operation Manual preview
F1 Series
Brand: SA Pages: 5
Samsung ML-6050 Manual Del Usuario preview
ML-6050
Brand: Samsung Pages: 82
Samsung ML-2525 Datasheet preview
ML-2525
Brand: Samsung Pages: 2
DASCO EBS-260 Cleaning Procedure preview
EBS-260
Brand: DASCO Pages: 2
MakerBot Replicator Mini+ Quick Start Manual preview
Replicator Mini+
Brand: MakerBot Pages: 2
MakerBot Replicator Mini Compact Reference Manual preview
Replicator Mini Compact
Brand: MakerBot Pages: 38
MakerBot Replicator 2 Quick Start Manual preview
Replicator 2
Brand: MakerBot Pages: 14
SainSmart Prusa i3 Troubleshooting Manual preview
Prusa i3
Brand: SainSmart Pages: 13
Xerox CX Visual Reference Manual preview
CX
Brand: Xerox Pages: 12
Oki C5550 MFP Reference Manual preview
C5550 MFP
Brand: Oki Pages: 167
Oki C610dn Manual De L'Utilisateur preview
C610dn
Brand: Oki Pages: 116
Oki C610dn Material Safety Data Sheet preview
C610dn
Brand: Oki Pages: 52
Oki C6000dn Manual Do Utilizador preview
C6000dn
Brand: Oki Pages: 331
Oki C6000dn Setup Manual preview
C6000dn
Brand: Oki Pages: 36
Oki C5800Ldn Series Reference Manual preview
C5800Ldn Series
Brand: Oki Pages: 143
Oki C710dn Guía Del Usuario preview
C710dn
Brand: Oki Pages: 101
Oki C710 Brochure & Specs preview
C710
Brand: Oki Pages: 6
Oki B6250dn Safety And Warranty Manual preview
B6250dn
Brand: Oki Pages: 36

Brands by name

Popular brands

Load more brands