manualshive.com logo in svg

Brother 9500 - HL 1660EN B/W Laser Printer, User Manual

The Brother 9500 - HL 1660EN B/W Laser Printer is an exceptional printing device that delivers sharp black and white documents with incredible speed and precision. To maximize your printer's potential, make sure to grab the free User Manual available for download at manualshive.com and unlock its full range of features and functionalities.

Share
Download
background image

USER’S GUIDE

5–8

The following capacity of SIMM can be installed:
  • 1 Mbyte HITACHI HB56D25632B-6A, -7A, -8A

   MITSUBISHI MH25632BJ-7, -8

  • 2 Mbyte HITACHI HB56D51232B-6A, -7A, -8A

   MITSUBISHI MH51232BJ-7, -8

  • 4 Mbyte HITACHI HB56A132BV-7A, -7AL, -7B, -7BL, -8AL, -8B, 

-8BL

   MITSUBISHI MH1M32ADJ-7, -8

  • 8 Mbyte HITACHI HB56A232BT-7A, -7AL, -7B, -7BL

   MITSUBISHI MH2M32EJ-7, -8, MH2M32DJ-7, -8

  • 16 Mbyte TOSHIBA THM324000BSG-60, -70, -80
  • 32 Mbyte TOSHIBA THM328020BSG-60, -70, -80

In general, the SIMM must have the following specifications:

Type:

72 pin and 32 bit or 36 bit output

Access Time: 80 nsec. or less
Capacity:

1, 2, 4, 8, 16 or 32 Mbyte

Height:

46mm (1.8 inches) or less

There are 40 bit output SIMMs for workstations. Such SIMMs do not fit
this printer.
For SIMMs and installation, consult the dealer where you purchased the
printer.

When you install SIMMs, follow these steps:

1. Turn off the printer and unplug the power cord from the wall socket.

✒

  Note

Be sure to turn off the power to the printer before installing or removing
the SIMMs.

2. Open the top cover of the printer.

3. Push the tab located on the left inside the printer to unlock the left side

cover.

Fig. 5-5  Unlocking the Left Side Cover

Summary of Contents for 9500 - HL 1660EN B/W Laser Printer



































































































































































































































































Reviews:

No comments

Related manuals for 9500 - HL 1660EN B/W Laser Printer

Canon TR8600 Series Getting Started preview
TR8600 Series
Brand: Canon Pages: 20
Canon PIXMA TS9100 Series Getting Started preview
PIXMA TS9100 Series
Brand: Canon Pages: 100
Canon PIXMA TS8120 Getting Started preview
PIXMA TS8120
Brand: Canon Pages: 100
Canon N 1000 Setup Manual preview
N 1000
Brand: Canon Pages: 105
Canon Pixma G1010 Series Getting Started preview
Pixma G1010 Series
Brand: Canon Pages: 16
Canon PRO-4000S Setup Manual preview
PRO-4000S
Brand: Canon Pages: 14
Canon iP1500 - PIXMA Color Inkjet Printer Service Manual preview
iP1500 - PIXMA Color Inkjet Printer
Brand: Canon Pages: 21
Canon S820D Quick Start Manual preview
S820D
Brand: Canon Pages: 68
Canon iP4500 - PIXMA Color Inkjet Printer Easy Setup Instructions preview
iP4500 - PIXMA Color Inkjet Printer
Brand: Canon Pages: 2
Canon Pixma TS3400 Series Manual preview
Pixma TS3400 Series
Brand: Canon Pages: 76
Canon MAXIFY GX4000 Series Getting Started preview
MAXIFY GX4000 Series
Brand: Canon Pages: 59
Kyocera ECOSYS M8124cidn Quick Manual preview
ECOSYS M8124cidn
Brand: Kyocera Pages: 44
Ravas PR-INT-MX-RAVAS-ABLE Manual preview
PR-INT-MX-RAVAS-ABLE
Brand: Ravas Pages: 26
Peroworx Infinito User Manual preview
Infinito
Brand: Peroworx Pages: 23
Intellisystem ThermalTronix TT-1260S-UTCM User Manual preview
ThermalTronix TT-1260S-UTCM
Brand: Intellisystem Pages: 18
Pantum L2710 Series User Manual preview
L2710 Series
Brand: Pantum Pages: 164
Citizen CT-S310 User Manual preview
CT-S310
Brand: Citizen Pages: 3
Xerox 8860MFPD - Multifunction Inkjet Printer Evaluator Manual preview
8860MFPD - Multifunction Inkjet Printer
Brand: Xerox Pages: 16

Brands by name

Popular brands

Load more brands