manualshive.com logo in svg

Brother 888-P30, Operation Manual

Share
Download
Brother 888-P30 Operation Manual Download Page 58

Updating Your Machine’s Software

56

The machine’s software can be updated using USB flash 
drive. 
When an update program is available on Brother support 
website at https://s.brother/cpjar/, please download the 
file(s) following the instructions on the website and steps 
listed below.
When using the wireless function, the update mark is 
displayed on the wireless LAN key.

: Updated software is available on our website. 

Update the software.

: No updated software is available.

Version information can be checked from the settings 
screen. (page 14)

a

Turn on the machine while pressing and holding 

(Needle position button).

The following screen appears.

b

Insert the USB flash drive into the USB port on the 
machine.

c

Touch .

• Do not turn off the machine during the update.

When updating is finished, the completion message 
appears.

d

Remove the USB flash drive, and turn the machine off 
and on again.

Updating Your Machine’s Software

Note

• Save only the update file on the USB flash drive.

Summary of Contents for 888-P30





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands