manualshive.com logo in svg

Brother 888-P30, Operation Manual

Share
Download
Brother 888-P30 Operation Manual Download Page 14

Turning the Machine On/Off

12

a

Make sure that the machine is turned off (the main 
power switch on the right side of the machine is set to 
“

”), and then plug the power cord into the power 

supply jack underneath it.

b

Insert the plug of the power cord into a household 
electrical outlet.

1

Power supply jack

2

Main power switch

c

Press the right side of the main power switch to turn 
the machine on (set it to “I”).

The light, LCD and the “Start/Stop” button light up 
when the machine is turned on.

d

When the machine is turned on, the opening movie is 
played. Touch anywhere on the screen.

e

To turn off the machine, press the left side of the main 
power switch (set it to “

”).

 CAUTION

• (For  U.S.A.  only) 

This appliance has a polarized plug (one blade 
wider than the other). To reduce the risk of 
electrical shock, this plug is intended to fit in a 
polarized electrical outlet only one way.
If the plug does not fit fully in the electrical 
outlet, reverse the plug. If it still does not fit, 
contact a qualified electrician to install the 
proper electrical outlet. Do not modify the 
plug in any way.

Memo

• If the machine is turned off in the middle of 

embroidering, the operation will resume after 
turning the power on again.

1

2

Note

When you first turn on the machine:

• Select the display language for the LCD.

• The following message about a wireless LAN 

connection appears. To set up a connection, touch 

, and then refer to steps 

c

 through 

f

 in 

“Using the wizard to set up the wireless network 
connection” on page 15 to finish setting up a 
wireless LAN connection.

Summary of Contents for 888-P30





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands