VI
- 1
CHAPTER
VI
TROUBLESHOOTING
1.
INTRODUCTION
1.1 Initial Check
(1) Operating environment
Check if:
1)
The source voltage stays within ±10% from the rating voltage shown on the rating
label.
2)
The printer is installed on a solid, level surface.
3)
The room temperature is maintained between 10°C and 32.5°C. The relative humidity
is maintained between 20% and 80%.
4)
The printer is not exposed to ammonia fumes or other harmful gases.
5)
The printer is not located in a hot or humid area (such as near water or a humidifier), in
a cold place (such as outlet of an air conditioner), near open flames or in a dusty place.
6)
The printer is not exposed to direct sunlight.
7)
The room is well-ventilated.
(2) Printer paper
Check if:
1)
A recommended type of print paper is being used (if the paper is too thick or too thin,
or tends to curl, paper jams or paper feed problems may occur, or prints may be
blurred).
2)
The print paper is damped. [If so, use fresh paper, and check whether the print quality
improve or not.]
(3) Consumables
Check if:
1)
The message "16 TONER EMPTY" is not shown on the status display when a
cartridge is installed in the printer . [If the message is displayed, replace the cartridge
with a new one. If blank spots occur on prints, take out the EP-ED cartridge and slowly
rock it to distribute the toner evenly.]
(4) Others
Check if:
The transfer guide and feed guide are clean. [If not, clean them with a damp cloth.]
Condensation:
When the printer is moved from a cold room into a warm room in cold weather,
condensation may occur inside the printer, causing various problems as below:
1)
Condensation on the optical surfaces such as the scanning mirror, lenses, the reflection
mirror and the protection glass may cause the print image to be light.
2)
If the photosensitive drum is cold, the electrical resistance of the photosensitive layer
gets high, making it impossible to obtain a correct contrast in printing.
3)
Condensation on the pick-up guide and feed guide plates may cause paper feed
troubles.
If condensation has occurred, wipe the effected units or parts with a dry cloth.
If an EP-ED cartridge is unsealed soon after moved from a cold room to a warm room,
condensation may occur inside the cartridge, which may cause incorrect image. Instruct the user
to allow the cartridge to come to room temperature before unsealing it. This will take one to
two hours.
Summary of Contents for 1660e - B/W Laser Printer
