BRONKHORST ES-FLOW 1 C Series Instruction Manual Download

Page: 29 / 41

Bronkhorst®

Instruction Manual ES-FLOW™ 1xxC

9.17.153A

6.1.4

Network configuration

Changes made to the network settings will

not

be restored by a factory reset.

Default configuration

Network configuration is done ex factory as indicated on the serial number label or in the technical specifications. The table

below shows the supported configurations for the available interface protocols (default settings are printed in bold):

Protocol

ProPar

(RS-232)

FLOW-BUS

(RS-485)

Modbus

(RTU/ASCII)

PROFIBUS DP

CANopen

DeviceNet™

Address

…125

…247

0…

126

1…

127

0…

Baud Rate

9600

19200

38400

57600

115200

230400

460800

187500

400000

9600

19200

38400

56000

57600

115200

128000

256000

(autodetect)

9600

19200

45450

93750

187500

500000

1500000

3000000

6000000

12000000

10000

20000

50000

125000

250000

500000

800000

1000000

125000

250000

500000

Parity

0, 1,

Network configuration for Ethernet based fieldbus types is done automatically via the Ethernet protocol.

Communication via fieldbus connector (RS-485)

Use the following parameters to configure the instrument for communication through the fieldbus connector (5-pin M12):

Fieldbus 1 Address

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…255

199

125/10

0x0FAA/4011

Fieldbus 1 Baud Rate

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned long

0…1.0E10

201

125/9

0xFD48…0xFD49/64841…64842

Fieldbus 1 Parity

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…2

335

125/12

0x0FAC/4013

The following values are supported:

Value

Description

No parity

Odd parity

Even parity

Communication via standard connector (RS-232/RS-485)

Use the following parameters to configure the instrument for communication through the 8-pin M12 connector:

Fieldbus 2 Address

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…255

309

124/10

0x0F8A/3979

Summary of Contents for ES-FLOW 1 C Series










































Search results

Summary of Contents for ES-FLOW 1 C Series

Reviews:

Related manuals for ES-FLOW 1 C Series

Brands by name

Popular brands

BRONKHORST ES-FLOW 1 C Series, Instruction Manual

Search results

Summary of Contents for ES-FLOW 1 C Series

Reviews:

Related manuals for ES-FLOW 1 C Series

Brands by name

Popular brands