background image

OPERATING INSTRUCTIONS 

|  KOBOLD  D 1600

     

 

EB 800.1600

Before use
Please read all the information contained in these operating instructions carefully. They contain 
important instructions for use, safety and maintenance of the appliance. Keep these operating 
instructions in a safe place and pass them on to further users if necessary. Observe the safety 
instructions.

Contents Page

Attention! Important safety instructions – Read carefully before starting up! 

 6

1. Starting up 

 

 

7

2. Fitting or changing a bulb 

 

8

3. Mounting and removing reflectors and adapters 

8

4. Fitting and removing accessories   

8

5. Focusing 

 

 

9

6. Operating the lamp with a Para   

9

7. Operating modes  

 

9

8. Display on ballast unit 

 

10

9. Protective circuits in the ballast unit 

10

10. Fault diagnosis table 

 

11

11. Operating Kobold ballast units from a motor-generator set 

11

12. Controls and display elements ballast unit EB 800.1600 

12

13. Technical data, ballast unit EB 800.1600 

12

14. Controls and display elements, lamp D 1600 

14

15. Technical data, lamp D 1600 

 

16

16. Order numbers for spare parts and accessories 

16

17. Environmental protection information 

16

Summary of Contents for D 1600
















Reviews: