Brocade Communications Systems VDX 6710-54 Installation Procedure Download Page 2

2 of 10

Flush Mount Rack Kit Installation Procedure

53-1002127-03

Copyright © 2010-2013 Brocade Communications Systems, Inc. All Rights Reserved.

ADX, AnyIO, Brocade, Brocade Assurance, the B-wing symbol, DCX, Fabric OS, ICX, MLX, MyBrocade, OpenScript, VCS, VDX, and Vyatta are 
registered trademarks, and HyperEdge, The Effortless Network, and The On-Demand Data Center are trademarks of Brocade Communications 
Systems, Inc., in the United States and/or in other countries. Other brands, products, or service names mentioned may be trademarks of their 
respective owners.

Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, 
equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time, 
without notice, and assumes no responsibility for its use. This informational document describes features that may not be currently available. 
Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in this document may 
require an export license from the United States government.

The authors and Brocade Communications Systems, Inc. shall have no liability or responsibility to any person or entity with respect to any loss, 
cost, liability, or damages arising from the information contained in this book or the computer programs that accompany it.

The product described by this document may contain “open source” software covered by the GNU General Public License or other open source 
license agreements. To find out which open source software is included in Brocade products, view the licensing terms applicable to the open 
source software, and obtain a copy of the programming source code, please visit 

http://www.brocade.com/support/oscd

.

Brocade Communications Systems, Incorporated

Document History

Corporate and Latin American Headquarters
Brocade Communications Systems, Inc.
130 Holger Way
San Jose, CA 95134 
Tel: 1-408-333-8000 
Fax: 1-408-333-8101 
E-mail: [email protected] 

Asia-Pacific Headquarters
Brocade Communications Systems China HK, Ltd.
No. 1 Guanghua Road
Chao Yang District
Units 2718 and 2818
Beijing 100020, China
Tel: +8610 6588 8888
Fax: +8610 6588 9999
E-mail: [email protected]

European Headquarters
Brocade Communications Switzerland Sàrl
Centre Swissair
Tour B - 4ème étage
29, Route de l'Aéroport
Case Postale 105
CH-1215 Genève 15
Switzerland 
Tel: +41 22 799 5640
Fax: +41 22 799 5641
E-mail: [email protected] 

Asia-Pacific Headquarters
Brocade Communications Systems Co., Ltd. (Shenzhen WFOE)
Citic Plaza
No. 233 Tian He Road North
Unit 1308 – 13th Floor
Guangzhou, China
Tel: +8620 3891 2000
Fax: +8620 3891 2111
E-mail: [email protected]

Document Title

Publication Number

Summary of Changes

Date

Flush Mount Rack Kit Installation Procedure

53-1002127-01

New document

December 2010

Flush Mount Rack Kit Installation Procedure

53-1002127-02

Added support for VDX 
6710 and VDX 6730 
models

September 2011

Flush Mount Rack Kit Installation Procedure

53-1002127-03

Added support for VDX 
6740 model

July 2013

Summary of Contents for VDX 6710-54











Reviews: