Brocade Communications Systems Converged Enhanced Ethernet 8000 Administrator'S Manual Download Page 56 | Manualshive

Page: 56 / 168

background image

34

Converged Enhanced Ethernet Administrator’s Guide

53-1002163-02

High availability

5

DRAFT: BROCADE CONFIDENTIAL

Every configuration is either fully committed or not, but never “half-complete.” If you had started
executing the copy startup running command, it will be resumed after failover before any new CLI is
allowed to be executed.

High availability reference

This section contains reference tables for high availability.

TABLE 10

State preservation during CP failover

Operation, data, or state

Expected behavior

CLIs that are being executed when
the HA failover occurs.

All telnet/ssh sessions are disconnected and need to be reestablished after
failover.
Any CLI operation under progress will either be fully committed if its
execution had started on active CP or not executed completely.
The vty timeout configuration is preserved across failover.

Running and Startup configurations The running and startup configuration is preserved.

All other configuration files are preserved.

L2 forwarding table

This item is preserved during failover.

VLAN table and state

This item is preserved during failover.

Static Multicast MAC DA

This item is preserved during failover.

Dynamic Multicast MAC DA
(learned via IGMP snooping)

This item is preserved during failover.

MAC learning process

MAC learning entries that are in the ASIC queue but yet to be processed by
software is flushed.

MAC ageing timer

The timer is restarted after the failover.

Station moves during failover

Station moves are not detected.

Interface state

Preserved as long as the interfaces are either in a shut or no-shut state. Any
interface which is not fully initialized is reset.

Interface counters

This item is preserved during failover.

Interface counters related to CoS,
Flow control, RED Alarms and other
configuration

This item is preserved during failover, however since interface counters are
not preserved, the alarms are restarted upon HA failover.

xSTP Port STP state

This item is preserved as long as the ports are in a steady state, otherwise
the port state machine is reset.

IGMP snooping – Dynamically
learned groups

This item is preserved during failover.

Static, Dynamic Standard, and
Brocade LAGs

This item is preserved during failover.

ACL policies

This item is preserved during failover, however the ACL counters are not
preserved.

LLDP, neighbor information,
profiles, or DCBX state machine

This item is preserved during failover.

QoS policies

This item is preserved during failover.

Port authentication state

Preserved during failover, as long as the ports are in a steady state,
otherwise the port state machine are reset.

SNMP sessions

Reset during failover. SNMP manager must reconnect after the failover.

«
...
54
55
56
57
58
...
»

Summary of Contents for Converged Enhanced Ethernet 8000









































































































































































Reviews:

No comments

Related manuals for Converged Enhanced Ethernet 8000

Brand: Abocom Pages: 11

Brand: Abocom Pages: 19

Brand: JCG Pages: 3

Brand: Supero Pages: 68

BroadLink SP3353

Brand: MicroNet Pages: 66

Brand: Speedtouch Pages: 124

Brand: VCS Pages: 118

Super Sound Set SR-JV80-07

Brand: Roland Pages: 8

Brand: Schrack Technik Pages: 2

Brand: EVOC Pages: 57

Brand: Gemtek Systems Pages: 51

Brand: Kontron Pages: 19

Brand: RubyTech Pages: 25

Brand: Aaeon Pages: 61

Brand: Gigabyte Pages: 18

Brand: Renesas Pages: 746

Brand: Rolls Pages: 1

Brand: Fluke Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands