Brocade Communications Systems Converged Enhanced Ethernet 8000 Administrator'S Manual Download Page 45 | Manualshive

Page: 45 / 168

background image

Converged Enhanced Ethernet Administrator’s Guide

23

53-1002163-02

Flash file management commands

3

DRAFT: BROCADE CONFIDENTIAL

Archiving the startup configuration file

This tasks allows you to archive the startup configuration to an archive folder on an FTP site. To
archive the startup configuration, perform the following task from privileged EXEC mode.

Enter the copy command to archive the startup configuration file.

switch#

copy startup-config

ftp://jsmith:[email protected]/archive/config_file]

Restore an archived startup configuration file

To restore the startup configuration, perform the following task from privileged EXEC mode.

Enter the copy command to restore the startup configuration file.

switch#

copy startup-config

ftp://jsmith:[email protected]/archive/config_file]

Flash file management commands

Table 7

describes the common tasks used to manage Flash files. The

Converged Enhanced

Ethernet Command Reference

contains complete information on all available CLI commands.

NOTE

Use of the flash:// prefix is optional.

The tasks listed in

Table 7

are performed from privileged EXEC mode.

Debugging and logging commands

Table 8

describes the tasks related to debugging and logging commands. The

Converged

Enhanced Ethernet Command Reference

contains complete information on all available CLI

commands.

TABLE 7

CEE Flash memory file management commands

Task

Command

List the files in the Flash memory directory.

switch#

dir

Delete a file from the Flash memory directory.

switch#

delete

flash://example_filename

Erase all the files in the Flash memory directory.
NOTE: This command erases

all

the files in the

Flash directory except the default startup
configuration file which is programmed as
a manufacturing default.

switch#

erase flash

% Warning: Erasing flash filesystem will
remove all files in flash://.
Continue to erase?(y/n):

y

Rename a file in the Flash.

switch#

rename filename new_filename

Display the contents of a file in the Flash memory
directory.

switch#

show file

flash://example_filename

«
...
43
44
45
46
47
...
»

Summary of Contents for Converged Enhanced Ethernet 8000









































































































































































Reviews:

No comments

Related manuals for Converged Enhanced Ethernet 8000

Brand: Paradyne Pages: 16

3CR860-95 - OfficeConnect Secure Router

Brand: 3Com Pages: 2

Brand: 3Com Pages: 26

Brand: LaCie Pages: 4

Brand: LaCie Pages: 4

Brand: PaloAlto Networks Pages: 3

VigorIPPBX 2820 Series

Brand: Draytek Pages: 29

Brand: ?omtime Pages: 62

Brand: Qlogic Pages: 2

Brand: UHP Pages: 15

Brand: Ubiquiti Pages: 21

Brand: Z3 Technology Pages: 67

Brand: Tripp Lite Pages: 3

Brand: Konica Minolta Pages: 31

High-Precision AD/DA Board

Brand: Waveshare Pages: 8

Brand: Airlink101 Pages: 64

Brand: ETAS Pages: 29

Brand: Mod Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands