Broadway Limited Steam Locomotive Operator'S Manual Download Page 23

Page: 23 / 50

Automatic

Operation

Take Control

Forward

Reverse

Neutral

Function

Key

Operation

Steam

Blower

Off after 10

sec

Off after 10

sec

On after 10

sec

Toggles

Steam

Blower

•

Take Control of Automatic Steam Blower with the F4 key to stop

automatic operation and control whether the Steam Blower is on or

off.

Regardless of the state of the Blower (on or off), if you press the F4 key, the

steam Blower hiss will be set to on if the F4 key is “1” and off if the F4 key

is “0” and Automatic Control will be disabled. Thereafter, the steam Blower

hiss will respond only to the state of the F4 function. Automatic Control will

be restored if the power is shut down and reapplied or if the F6 Start Up key

is double pressed in Neutral (see the description of Start Up on p. 25).

Three Stages of Shut Down: 1. Disconnect, 2. Standby, 3. Total Shut Down

(F9)

Engine Shut Down has three distinct stages that you can control. Each

stage is entered by double pressing the F9 key

Stage One: Disconnect

•

Double press the F9 key in Neutral to enter Disconnect. You will hear

a Long Air Let-off.

•

To leave Disconnect, either double press the F6 Start Up key

described in the Start Up section or double press the F9 key again to

reach the next stage of Shut Down, Standby.

If you double press the F9 key in Neutral, the electric motor drive will be

disconnected from the Quantum System. You will hear a Long Air Let-off

after entering Disconnect, which represents the locomotive’s reverse lever

being placed in the neutral position. Once in Disconnect, the throttle can

be moved up and down without the steam engine moving. Instead, you will

hear the sound of steam gradually being vented through the throttle. All

function keys are active in Disconnect.

Note:

There is no affect on the throttle Sound-of-Power from Dynamic

Brake being on in Disconnect as there is in diesels.

Summary of Contents for Steam Locomotive



















































Search results

Summary of Contents for Steam Locomotive

Reviews:

Related manuals for Steam Locomotive

Brands by name

Popular brands

Broadway Limited Steam Locomotive, Operator'S Manual

Search results

Summary of Contents for Steam Locomotive

Reviews:

Related manuals for Steam Locomotive

Brands by name

Popular brands