Broadway Limited Steam Locomotive Operator'S Manual Download Page 10

Page: 10 / 50

throttle.

Sound of Power™

The steam locomotive will produce Sound-of-Power labored steam sound

effects if you have selected any of the Load settings from level 1 to 15.

Under acceleration, the Chuffing sounds will be more labored until the

locomotive has achieved its final speed where it will then produce standard

sounds appropriate to its throttle setting. Under deceleration, the engine

Chuffing sounds are less labored until it achieves its final speed where it will

again produce standard steam sounds appropriate to its throttle setting.

Helpers

Prototype Helpers are locomotives that are used to provide extra power

and/or braking for a heavily loaded train. These engines can be part of the

head-end consist or as mid-train helpers or as pushers at the end of the

train. Helper engines behave differently than the train’s lead locomotive.

Their whistles and bells are usually not operated and their lighting options

are different or not used at all.
When you make up your train using more than one locomotive, the

Quantum System allows you to easily program how each engine will

behave by selecting between a Lead engine, Mid Helper, End Helper,

or Pusher. Each type of Helper engine has different lighting and sound

characteristics as described in the table in the next section on Analog

Programming.

Normal and Reversed Direction

Quantum also allows you to reverse the directional sense of your

locomotive. This is normally not an issue with DC two-rail trains since all

engines will go in the same direction whether they are facing forwards or

backwards. However, certain features like Directional Lighting do depend

on the directional sense. For instance, if you program your engine to be

an End Helper for your consist, its tender Reverse Light operates when

the engine is moving in Reverse and the Headlight is disabled. This is

ideal for providing a Reverse Light for the consist. However, if this steam

locomotive is facing backwards at the end of a consist, the Reverse Light

faces forward and will be lit when the consist is moving Forward and there

will be no Reverse Light for the consist. The “Direction” program feature

will ensure that this End Helper’s backward facing Headlight will come on

only when the consist is backing up and the forward facing Reverse Light

Summary of Contents for Steam Locomotive



















































Search results

Summary of Contents for Steam Locomotive

Reviews:

Related manuals for Steam Locomotive

Brands by name

Popular brands

Broadway Limited Steam Locomotive, Operator'S Manual

Search results

Summary of Contents for Steam Locomotive

Reviews:

Related manuals for Steam Locomotive

Brands by name

Popular brands