manualshive.com logo in svg

Broadcast Tools Sentinel 3, Installation And Operation Manual

Share
Download
Broadcast Tools Sentinel 3 Installation And Operation Manual Download Page 8

e-mail: 

[email protected]   

voice: 

360.854.9559   

fax: 

866.783.1742

8

Switcher Sentinel

®

3 »Web Installation and Operation Manual

SETUP

Web Setup/Operation

Ethernet “Quick Start” guide

CAUTION! 

If you are not familiar with Ethernet enabled equipment, it may be use-

ful to contact your IT department, network administrator or network consultant for
help.  Assigning an IP address already in use by another device may cause problems
with your network!  Instructions for changing the IP address of the computer that
will be used for the configuration of this product are given here. Note that these
instructions are specifically for computers with the Windows XP operating system.
For setup using other operating systems, refer to the appropriate OS user’s manual.

Step 1:

Open the control panel by clicking on the start menu, click on settings, then

click on Control Panel. (Note that the control panel shown is in “Classic View”. If con-
trol panel is in “Category View” select the “Classic View” option before proceeding.)

WEBSITE:

Visit our web site for
product updates and
additional information.

Summary of Contents for Sentinel 3





























Reviews:

No comments

Brands by name

Popular brands

Load more brands