Broadcast Tools ICM-16/MHI Installation And Operation Manual Download Page 3

ee--m

maaiill::  

[email protected]   

vvooiiccee::  

360.854.9559   

ffaaxx::  

360.854.9479 

3

ICM-16/MHI Installation and Operation Manual

INTRODUCTION

INTRODUCTION

Thank you for your purchase of a Broadcast Tools® ICM-16/MHI, Intercom
Monitor/Headphone Interface (referred to as the MHI throughout this manu-
al).  We’re confident that this product will give you many years of dependable
service. This manual is intended to give you all the information needed to install
and operate the  Broadcast Tools® ICM-16/MHI.

SAFETY INFORMATION

Only qualified personnel should install Broadcast Tools® products.  Incorrect or
inappropriate use and/or installation could result in a hazardous condition.

WHO TO CONTACT FOR HELP

If you have any questions regarding your product or you need assistance, please con-
tact your distributor from whom you purchased this equipment.

If you would like more information about Broadcast Tools® products, you may
reach us at:

Broadcast Tools, Inc.

131 State Street
Sedro-Woolley, WA 98284 USA
Voice: 360 . 854 . 9559
Fax:

360 . 854 . 9479

Internet Home Page: www.broadcasttools.com
E-mail:

[email protected]

THANK YOU FOR CHOOSING 

BROADCAST TOOLS® BRAND PRODUCTS!

CAUTION!

Broadcast Tools®

Products, as with any
electronic device, can
fail without warning.
Do not use this product
in applications where a
life threatening condition
could result due to failure.

NOTE:

This manual should be
read thoroughly before
installation and operation.

WEBSITE:

Visit our web site for
product updates and
additional information

Summary of Contents for ICM-16/MHI
















Reviews: